Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
I found a issue, I open a sample project " v2.5.0\nrf\sample\cellular\location"
when I click "Add build configuration", no nrf9160 option and only nrf52840 can be selected...
Hi, I am trying to do pwm a rgb led using nrf54l15dk and custom board using nrf54l15 on port1 with pin connections on (p1.10, p1.8 and p1.13 for custom) or on (p1.11, p1.12...
Greetings,
I have worked with the MCUBoot and its Serial Recovery feature with success and recently tried to enable the CONFIG_BOOT_SERIAL_WAIT_FOR_DFU option ( as well...
Hello,
I am intending to extract audio from the onboard microphone of nrf5340-audio-dk.
I used the nrf5340_audio application as reference but cutting off the bluetooth...
Hi,
I'm trying to use same UART channel on both project-specific purpose and MCUmgr DFU. However, when I enable the option CONFIG_MCUMGR_TRANSPORT_UART, the code reset's...
Hi, I used in my hw design Config. 6 for nRF52840 QIAA aQFN73
https://docs.nordicsemi.com/bundle/ps_nrf52840/page/ref_circuitry.html#ariaid-title7
The question is how...
Hi,
We are defining a BLE interface for our product, choosing SIG and custom services, and while working on BLE for years now, I have still questions on how to design the...
How to configure the SPIM if i have defined my MOSI/MISO/SCK pins in the device overlay file, shown below:
&pinctrl { spi0_default: spi0_default { group1 { psels = <NRF_PSEL...
We are developing a board with an nRF54L15 module that interfaces with a SPI device. We want to use 3-wire spi, so the MISO and MOSI lines are shorted (according to the datasheet...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2.
I am currently using Pawr. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hello Nordic Support,
Currently, we are using nRF5 SDK for Thread and Zigbee 4.2.0 for our Zigbee coordinator application running on nrf52840.
We understand that this...
I am using the NRF5340 Audio DK , and the onboard PMIC is the NPM1100 . I am not using the onboard audio codec of the DK. Instead, I am powering an external audio codec module...
Hi,
I've just completed Lesson 2 Exercise 3 and found that BLE Provisioning does not work from the iPhone version of the app. The problem seems to be related to Version...
Hi everyone,
Environment:
nRF Connect SDK v2.8.0
Light Switch example
I’m currently working on implementing a Zigbee Sleepy End Device (SED) for a battery-operated...
Hello,
I'm currently using the nRF9151-DK hardware to develop our product based on the nRF9151 SiP . We selected the ncs-serial-modem firmware, and the modem is controlled...
