Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Hi,
I'm trying to collect modem trace from a custom nRF9160 board which is connected to the PC with a FTDI FT2232 UART-USB converter (USB vendor id 0406, product id 6010...
All - We have an nRF52340 based design which when tested with the system off demo available in NCS v1.5.1 gives a system off current of <1uA.
We have a second design using...
Hi.
I just downloaded the new nRF5 SDK v17.1.
The first example I tried, the ble_app_template, the Keil uVision project for pca10056 is setup to use a fixed device pack...
Hello,
We are using an nRF52 DK as part of our QC process to send test commands to one of our devices and record responses. However, I think that the people running the...
Hello! I'm reading the documentation that exists for the nRF5340 and struggle a bit about the Secure attribute unit (SAU) If you read the ARM documentation about TrustZone...
Hello.
I am developing Central device which support LESC.
I have some question about connect to Servers which have diferent LE security
for example case, one of...
Hello,
I am using nrf sdk 1.5.1 and trying to connect the Nrf ZigBee router(light bulb example) with Digi Xbee Coordinator but it doesn't seem to connect. I observed the...
Hello all,
I'm interacting with some nodes in a test network:
setup: 10x nrf52840 DK (PCA10056) boards loaded with the following software.
1x Coordinator ( Zigbee CLI...
Hello,
I'm using nRF SDK v1.6.0 with nRF9160 development board. I did minimum changes to Asset_Tracker_v2 application (enable debug log, set up for my aws account and to...
Migrating from nRF5 SDK to nRF Connect (Zephyr) what is the best way to define pin names using a custom board? in nRF5 SDK the header file custom_board.h usually defines the...
If I enable CONFIG_ASSERT=y this example will crash (or code using the DF APIs)
To reproduce:
- nRF Connect 1.6.1
- In direction_finding_connectionless_rx add CONFIG_ASSERT...
HI Devzon
currently my customer has some question about the power consumption difference between "LOWLATENCY" & "LOWPOWER" on NRF5340 GPIOTE
we useing PPK2 to testing...
hi support team，
customer have one problem that saadc is high rate sample at about 800hz, it runs ok, but after ble connection and send data to device from mobile device...
Hi , My application works on ncs v1.3.0, and now I need to upgrade the SDK to upgrade the application to work on ncs v1.5.1. I have completed the application development on...
Hi,
I am developing a PCB with the nrf52840 chip. The chip is implemented as described in the datasheet ( Circuit configuration no. 6 for QIAA aQFN73 ), using the files...
