I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
What is the limitation of the total current we can source/sink at the same time in multiple pins for low Vdd?
I could find a similar question (and answer of 15mA...
Hello there, I am working on a customized nrf52832 board. For the limited size, the 32kHz crystal is not install because I think the clock from 32khz crystal can be replaced...
Hi all
I want to do a device firmware update via the bootloader, and I am unable to do so, as all attempts end with a disconnect from my Android phone (Pixel 4a). I can...
Hello!
Hardware: nrf52840 IDE: Segger Embedded Studio SDK: nrf5 SDK 17.0.2
I've been having issues with receiving USB HID IN reports on Android. If I send at an interval...
I'm trying to debug a usage fault in my NCS project using an nRF52833 DK. I can't seem to select the logging backend for coredumps. I have the following lines in my prj.conf...
Hello,
in my project i am using GSM module so i need to add UART to TEMPLATE example but i am getting error that "undefine reference to app_uart_init"
please resolve the...
Hi
The Zephyr mesh_demo project has been built correctly but I'm facing a problem when I flash it
C:\Users\OMAR\zephyrproject\zephyr\samples\bluetooth\mesh_demo> west...
Hello :)
I am using pca10056. Use SPIM to control the external flush memory of this board. I read the IC's surface, I recognized its name is MX25R6435F. (Is it correct ...
Hi. I've tried to build the TF-M Hello World sample using nRF Connect SDK and I get these two errors (which I think are related):
opening dependency file secure_fw\partitions...
Looking through the documentation and examples for the nRF9160, they all seem to be based on the Zephyr RTOS. I have 2 questions:
Is there any benefit (mainly from a power...
Dear Nordic,
Could you please advice me how to combine system off mode and bluetooth advertisements using Zephyr / nRF Connect SDK? Is there any clear example around?
...
Hello, I'm very new at nrf connect sdk. I tried to rebuild mqtt_sample and I got this error: opening dependency file modules\nrfxlib\nrfxlib\nrf_security\src\mbedtls\CMakeFiles...
Hi all,
I want to use TWIM1 on NRF5340, and I initialize it as follows:
But the return value of err is 0x0bad0005,
I guess may be TWIM1 is occupied by zephyr, because...
Hi,
I am trying to implement beacon-ing into my existing firmware of different beacon types. I have successfully generated an iBeacon and Eddystone-UID beacon using ble_advertising_advdata_update...
