Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hello Nordic team, Whilst porting our product from nRF Connect 2.4.1 to 2.9.1 we encountered the following problem. When compiling with ZIGBEE_FACTORY_RESET=n we get Seems...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
i'm looking for an extremely simple BLE beacon app, which advertises (say) at 1HZ and then enters a "low-power" sleep mode....
there are numerous samples included in the...
Hello forum ,
In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
I am in the process of integrating a custom display driver (ST7305) into my Zephyr-based project and have followed the necessary steps:
Placed the .c and .h source files...
I'm using SDK version 2.9.0 with an nRF52840 in a combined peripheral / central application.
The nRF52840 device starts advertising, but then after connecting (as a peripheral...
Hi,
I am trying to download the nrf connect toolchain in vs code but getting this error
Error: Failed with exit code 1. Failed to download toolchain bundle Caused by...
Hello.
I am developing an application based on IOS-nRF-Mesh-Library, and currently considering porting firmware upgrade function of IOS-nRF-Connect-Device-Manager for updating...
Dear All:
I don't have a le audio enabled phone, and i want to study the hci commands about cis and bis setup up processure.
Could you please provide some HCI logs from...
Hello there!
I'm trying to run the official, unmodified, version of the `WiFi Shell` sample targeting the `nrf7002dk/nrf5340/cpuapp` board and am currently getting:
...
Dear,
I recently upgraded my project from NCS 2.4.0 to NCS 2.9.0 and encountered an issue with the ST7789V display driver.
Previously, I used SPI0 to interface with the...
Hello, my application is running on a custom board. The BLE Host is on an nRF9160, the BLE Controller is on an nRF52820, and the SoCs are connected via UART. On my original...
Hello,
I am new to multicore programming. I tried to find without much success a complete VS Code sample project from Nordic targeting nrf5340 two cores; ideally with the...
I am attempting to connect my nrf52840/52811 DK to my custom PCB that contains nrf52840. The DK users guide describe the connections on the P19 debug out port but I can see...
Hi all,
This is for nrf9160 with firmware version 1.3.1.
I 'm trying to read back the certificates and comparing with a known CRC.
modem_key_mgmt_read is able to read...
