I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hello,
i'm interfacing with the nrf_modem_lib using posix socket API with offloading. The send is called separately from a dedicated thread to avoid any hanging of the rest...
The maximum current of my measuring board should be 8ma, but the maximum value measured by kit II is 24ma, and the average current of 100ua is correct,and the minimum value...
Hi,
Nordic nRF Connect SDK includes also the Zephyr repository with a number of examples. I am interested in the HCI UART example in Zephyr, and I want to open from Nordic...
Hi,
I am currently working on a project similar to this thread:
However, the thread stop updating. I followed what Einar suggested, to merge the Decawave example code...
Hi all,
I have an issue on my device. We have implement OTA update but sometimes, the nfr stucks on DFU mode after the update. Even if the update is succesfull.
We use...
Hi All.
I am checking battery autonomy with different settings in my Module (with an nRF52840 SoC inside) since, in my project, this is a critical restraint. I am feeding...
now, I need transfer data between nrf52840 (base on zephyr OS) and python app through PYSERIAL. Is it possible to use something like RTT or shell_uart to transmit/receive...
How do I switch between being SPIS/SPIM with the Zephyr library?
I am using ncs v1.9.1. I have code that works separately as a slave or master but I need to make it dynamic...
I want to use +8 dBm TX power so I added CONFIG_BT_CTLR_TX_PWR_PLUS_8 to my prj.conf, and then realised it doesn't do anything.
I then found set_tx_power() on these pages...
The problem: We are getting a hard fault immediately after jumping from the bootloader while trying to initialize the nRF USBD driver. The fault happens in nrfx_power_init...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
