Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
SDK 17_0_2
Hi!
I can't understand is it any possibility to wake up nRF32 from sleep mode via internal RTC timer?
For example- I set ADV duration 30 sec. After that time...
Hi Nordic team !
Is the licencing model linked with the Nordic OTA libraries available in github allows me to freely fork / modify / share a compatible version for Xamarin...
I have define CONFIG_NFCT_PINS_AS_GPIOS, but the pin is always low, even if the OUT register is high.
I have read 0x1000120C(NFCPINS), it is FFFFFFFF, what's wrong with...
Hi, After many attempts I was unable to make RPC_Host sample work ( link to the related nRF Connect SDK doc ). From SES in debugging mode, the network core gets stuck in an...
Hi,
I am writing a program to actively change the state of an LED, then sample the output voltage on the led pin using SAADC, then outputs the adc value to terminal every...
I bought the nRF52840 DK and want to start developing my first application. However, I am very overwhelmed by the documentation here infocenter.nordicsemi.com/index.jsp This...
Hi All, I have a problem with the UART interrupts on the nrf9160dk, the error code (-134 / -ENOTSUP) says that it is not supported. However, I don't know what might be the...
Hello everyone,
I'm unable to perform DFU over SMP BT with nRF Connect for iOS. I've already verified the process works with mcumgr (Ubuntu 20.04 LTS) and with nRF Connect...
I am trying to use the `fmfu_smp_svr` sample project, as described in nRF9160: Full modem firmware update using SMP Server , to perform a full modem firmware update.
The...
Dear ,
I am going to use SDK 17.0.2 spis example.
But I found it is 8 bit data width. I am going to use 16 bit data width .
Would you teach me how to change?
Hi all,
I am using NRF5340, and I want to use pin 0.14 for spim. However, I found it was used by QSPI, in zephry.dts:
So how can I close QSPI to use pin 0.14 freely...
Hi.
Below is used the same schematic for nRF52805 but with different placement for RF components.
What are the pros and cons of each one? Is there one that is "better...
Hi !
I want to successfully send CTE after the CRC of the broadcast packet by operating the RADIO register under the Manual configuration of NRF52833。At present, I can successfully...
Hi developer,
I am trying to understand Beacon behavior and program. I am using BLE_Central multilink example to get informaiton from Beacons.
I added the below code...
