Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Posting this as separate question as it got no traction in the other thread:
Why are there many of the same include files in the DFU example directory as in the S110 7...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
I debugging some function abnormal after OTA problem, and problem with disappear after redo OTA FW upgrade, duirng it I found a problem about Master Control Panel FW upgrade...
NRF52832
SDK 17.0.2
SoftDevice 132
I am connecting with telnet to an exposed RTT port to see the logs. I adjusted sdk_config.h to use RTT instead of UART logging. The...
Question 1:
The nRF9160 datasheet V2.0 claims the sensitivity is: CATM=-108dBm (mid band); NBIOT=-114dBm (mid band).
However when the unit connects, we get a printout...
So in the MQTT example the following function is used to write the CA certificate to the modem so a TLS connection can be setup.
In our code/TLS setup we want to use Client...
Sorry this is an urgent request and we could not find much information on the internet about this module. We have a tight schedule so it might be a good idea to post here...
Hi, Hope your are well, i am currently in the final part of my project where i am SPI Gyroscope float data from one nordic nrf52dk (S132) to another such that i can analyize...
I am running read str 0x3e000 12 via UART line but there is nothing which gets printed on the terminal.
Even if i write some hex value to a particular flash memory location...
Hi there,
I have set up the nRF2427 with the nRFgo Starter Kit motherboard (nRF6700). The motherboard is recognized and I have all of the 2.4GHz options available. I would...
Hello,
I am working on the nrf52832 board with SDK16.
I am using a custom BLE example.
My TWI and BLE code work ok individually but when I integrate them it does not...
Using S132 v7.2, I'm getting a hard fault at PC 0x00015810 (I see the flag set in SEGGER, and the console outputs a SOFTDEVICE ASSERT FAILED error) that I'm working on manually...
Hi,
The 'nRF Connect' SDK (v1.4.99-dev1) sample OpenThread CLI is programmed to receive 'ot' commands from UART console. When configured with multi-protocol support, the...
Hello,
I have a problem that sometimes the supl_client_session() function halts the system by not finishing and ending the session while getting the timeout expired SUPL...
Hi
I can't find fwid for sd132 7.2
|s132_nrf52_5.0.0|0x9D| |s132_nrf52_5.1.0|0xA5| |s132_nrf52_6.0.0|0xA8| |s132_nrf52_6.1.0|0xAF| |s132_nrf52_6.1.1|0xB7| |s132_nrf52_7...
Hi there,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the...
Hello, I use the internal crystal, the application in my board runs normally and it shows the board is in fast advertising state. However, I can't find bluetooth signal through...
I'm running the Zephyr hci_usb sample on a nRF52833DK to see if I can use it as a Bluetooth dongle on my Ubuntu dev machine. It appears as /dev/ttyACM0, so:
sudo btmon ...
