Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I'm attempting to add support for a custom ili9341 display to a project running on a the uBlox Nora dev kit. I'm currently using VS Code with nRF Connect SDK1.9.1. My question...
tried the proximity example to check pairing/auto-repairing using PCA10040 board. currently having not auto repaing after we power OFF/ON the device.
we are planning to...
Hi,
I encountered an error when I turned on NRF_LOG_BACKEND_RTT_ENABLED in a project:
"...section '.log_backends' will not fit in region ‘UNPLACED_SECTIONS’."
"region...
Hi All!
I am using nrf21540 along with nrf52833/20. My question is can it be possible to use nrf5 SDK instead of NCS? I have developed the application using nrf5 SDK and...
Dear nordic team,
we are successfully communicating our old nRF2401 shockburst design to a nRF5340 board; except for the CRC.
The challenge: the nRF2401 shockburst allowed...
Hello,
In function such as i2c_write and i2c_read does Zephyr check to make sure the device is not a NULL pointer? If not how would it react if it were passed one?
...
Hi,
I tried to run the "matter" light_bulb example from nrfconnect versions 2.0.0, 1.9.1 2.0.99, but failed to
to see blinking LEDs. I suspect this may have something...
Hello dear Nordic. I am reading your documentation and stuck on the following issue:
According to the SEQ[1].CNT register there are 3 pulses with different duty cycle...
Hello there,
The same code works reliably on dev kit but not on my customized hardware. By cutting the 32k external crystal jumper on the dev kit, the same failure can...
Hi,
I am working on nRF52840 dongle.
i am facing a issue with programming. before it i was trying to do it with arduino. i don't know its bootloader gets disturbed....
I build the asset_tracker with custom code added to it and working well. The build time messages are shown in the attached text file. There e %of Flash used in show thrice...
HI,
I'm trying to configure the MCUboot / Netboot with an external QSPI flash. I can do it for the APP core with MCUboot, however I get lost how it work with the NET core...
Hi Nordic team
We plan to develop a stereo bluetooth loudspeaker, that can be connected from any smartphone to stream audio.
The prefered audio output would be PWM since...
I am working on firmware for a custom board with an nRF9160. Specifically, I'm trying to get FOTA updates working, using the provided library functions for it. I had no issues...
