Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi,
I'm trying to run the zephyr/samples/drivers/adc/adc_dt example on the nRF54L15 DK .
I modified the board overlay file zephyr/samples/drivers/adc/adc_dt/boards/nrf54l15dk_nrf54l15_cpuapp...
Description:
I'm having an issue with my nRF52811 custom board where the device won't start BLE advertising after programming, but it works after cycling through GDB monitor...
Hello,
Following the NRF54L Express course I see that PWM duty cycle can be updated from RAM via EasyDMA but I can't see an example of how this can be done anywhere...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
When i flash i always get the this error: before this i had an another sensor the VL53L0X which worked perfectly.
[0Sensor device not ready! 0:00:00.254,119] <err> VL53L1X...
We are trying to develop a smart controller based on the nRF54L15 that supports a dynamically configurable number of buttons. We want users to be able to select the number...
Hi,
I’m trying to explore the capabilities of DECT NR+ technology using the nRF9151-DK. Are there any recommended external antennas that I would be able to use with this...
Hello,
we are building a custom PCB using the nPM1300. We need a low-noise 1V8 rail for a sensitive analog component and are wondering what the best setup for that would...
I’m working with the CRACEN peripheral on the nRF54L15 and I’m trying to understand the DMA User Tag field used in registers like `CRYPTMSTRDMA.FETCHTAG`.
The documentation...
Hello,
i'm working on a matter sensor on a nRF52840 Dongle and BME280.
The softaware is based on matter/temperature_sensor with config changes to support nRf52840 Dongle...
We are using the Nordic Semiconductor nRF7002-DK . In this board, both PS-Poll and No-PS-Poll power-saving modes are working as expected. However, when running in TWT (Target...
Hi,
we have a issue to find the right configuration to get the maximum throughput in a multiple connection scenario.
In our setup, we are using one central and three peripherals...
Dear Nordic,
We are performing current measurements on a nRF-9151 DK using the Power Profiler Kit II. The attached picture shows the 9151 and PPK-II connected. Notice that...
