Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi, I am using nRF connect sdk1.9.0 and modem firmware 1.3.1.
I have configured GPS to single fix mode.
err = nrf_modem_ gnss _fix_interval_set ( 0 );
err = nrf_modem_...
I have been trying for hours to get the LTE Sensor Gateway sample to work on my Thingy:91 (PCA20035) without success. According to the v2.0.2 README and the HCI low power...
Hi,
I would like to create a service that shows the current TX power of a peripheral during connection. I am using the Android nRF Connect app to connect to the nRF52833...
Hi:
I can't find the download address and description of the S110_NRF51822_7.1.0 protocol stack on your official website. I would like to know the version of BLE of this...
Hello, I encountered some issues with VS Code nRF environment. Kconfig will not open when clicked nor can I debug. When I try to debug it seems to be launching debug for a...
Hi
How can I read out the bootloader version from the main application which I defined in the zip packet (or merged hex) with nrfutil?
rfutil pkg generate --hw-version...
I'm using nRF Connect SDK v2.0.2 (in VSCode, w/ the plugin) on nRF52840-DKs.
Following the MPSL Timeslot sample , in the code shown below, I created a non-preemptible thread...
Hi
Currently I'm working on a Matter project with an nRF52840 board.
We have our own CSA issued vendor ID.
We want the light_bulb sample project to work with our vendor...
Hi Iam work on Linux 5.14.0-1011-oem #11-Ubuntu SMP Mon Dec 13 18:01:14 UTC 2021 x86_64 x86_64 x86_64 GNU/Linux
When I open VScode I got "Shell initialization conflicts...
Hi,
We are evaluating nRF5340 for our new product. We learned that nRF5340 can be used for LE Audio application. However, we want to know whether simultaneous BLE communication...
Hi,
We have developed a BLE module using Zephyr as RTOS on Espressif ESP32C3. Now we're looking to port the same application to the Nordic nRF52810. We have chosen nRF52810...
Hello,
I am working on a custom board using the BC833M ( https://www.digikey.com/en/products/detail/fanstel-corp/BC833M/13174321 ) which uses an nRF52833. I am using a rigid...
Hi,
Customers have reported the problem of dfu upgrade failure, and we also use the same type of mobile phone (iPhone 11 & iPhone XR) for testing. It is found that there...
Hello,
I am relatively new to the nRF Connect SDK and I'm developing an application for nRF9160DK on toolchain version 2.0.2.
I am working on a non-secure application...
Hi, I am trying intialize the RTC in ncs using nrfx drivers and then connect it tick event to a saadc sampling event using a ppi channel. I learnt that RTC0 and RTC1 are used...
