Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I'm using s132.
I'm using the app timer with the app scheduler.
I'm running a simple loop and constantly scheduling the timer in the timer callback.
The callback works...
Dear forum,
I want to achive low energy consumption for a BM833 (with crystal).
From the following thread, I could deduct, that running the softdevice, an average of 300...
Hi,
OS: Windows 10
SW used is Segger IDE, nrfCOnnect for desktop to program HW used is nRF 52480 dongle PCA10059
I am starting using nRF 52480 USB dongle, I need to...
I am working with nrf52840DK, SDK v17.1.0.
I compiled and downloaded the open bootloader project to the DK using SES (No errors and verification says OK). According to...
Hi,
We wanted to add an additional flash section to the linker.cmd file located in the zephyr folder of the project folder. However, when we make changes to the memory section...
We have a situation where the network core of the nRF5340 has been given control of Port 0/GPIO pin X (GPIO0->PIN_CFG[X].MCUSEL = 1 on the application core). The network core...
I have 2 dongles that I've somehow managed to brick (I don't remember the details on how i did it). One of them goes into DFU bootloader mode when I plug it in but shows up...
Hi,
I am modifying the code to asset_tracker_v2 on Thingy91 to send data to my own server instead of Azure / AWS / Nordic Cloud. I am getting error code -35 (EDEADLK) when...
The discussion in https://devzone.nordicsemi.com/f/nordic-q-a/79364/maximum-number-of-bytes-that-can-be-used-in-beacon-advertising suggests that we should be able to populate...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
Hello,
I'm running the Asset Tracker V2 NCS 1.7.0 conected to the nRF Cloud. I'm using a Thingy:91 with external GPS antenna.
The GPS position is being correctly aquired...
Hello ,I am starting new development in Nordic environment and my system configuration is intel i3 with 8gb ram.
Still it is way too much slow to open nrf connect for desktop...
Hello everyone,
i want to use the 52810 to write into a SD -card, i use a slightly modified fatfs example.
The problem is, the SD card will not initialize as the p_event...
