Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I have a characteristic that i want to change to allow notification.
But when I include the presently commented line below (that sets notify to 1), the code breaks, which...
We have a prototype device that disconnects and reconnects frequently. When moving from a BLE 4.2 chip to the nrf52840 (BLE 5), we noticed that the time to complete the initial...
Hello,
I am developing a project with a host processor and Minew BT module with NRF52811. The module and the host processor are communicating via I2C (TWIS). The host processor...
Hi,all
As said above, i've tested two laptops, and this situation happened. I have no idea why this will happen. Is there may any problem with the c onnection parameters...
I used stm32 as master and nordic board as a slave , in stm32 i used spi2 where my configuration is , baud rate is 4MBits/s , clock polarity high , clock phase 1 edge and...
I am trying to locate documentation that has recommended solder paste and reflow specifications for the QFN package. I see there was a similar request made quite some time...
Hi,
When looking at the release notes for the latest nrf9160 modem firmware, it says that the B0 devices are for development only, and B1 for production. I have a number...
Hi there!
Back again with another question. Now that I've finaly managed to get the Bitmap image to show on the display (ST7735), I noticed the playback of audio from the...
Hi What is the better way to add multiple generic on off element to light switch server application. currently planing to add seperate simple_on_off_server_t m_server_x and...
Hi~.
I have an inquiry about sleep and wake up of the nRF52840 in high voltage mode.
Hardware and power design configuration
I am trying to use high voltage mode by...
When the application is started I get the following error:
<error> peer_manager_pds: Could not initialize flash storage. fds_init() returned 0x860A. 00> 00> <error> peer_manager...
Hi there!
I have an SD card reader and ST7735 connected to an nRF52850 DK, both working fine. Furthermore, I 'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK...
Hello everybody,
I´m trying to add a custom service to the ble_app_buttonless_dfu example in sdk 17.0.2 . Therfore i increment the NRF_SDH_BLE_VS_UUID_COUNT but this results...
Hello, I´m using nRF52DK BLE module with ContikiNG and I seem to be having issues when trying to connect with the device using the mac address. I´m trying to setup the basic...
Dear all, I'm new on nordic and I have to combine a bootloader BLE+UART. I read some threads but I can't to combine UART + BLE. Can I have an help?
Thanks in advance
