Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
My custom device uses nRF9151 and we're using SDK 2.6.0 with modem firmware 2.0.1.
When the device connects to the LTE network it derives a default APN, however, my provider...
Hi,
I’m exploring the use of the Thread/Matter protocol for a smart lighting system. My goal is to have the system communicate seamlessly with the cloud—allowing commands...
I am using a LattePanda 3 Delta running an Ubuntu server OS (x86) headlessly. I am using a RS-232 cable to obtain the modem trace from my custom board, which uses an nRF9160...
Hi,
We are currently starting a project using the nRF52832 as our controller, Segger Embedded Studio 5.42a as our IDE, and nRF5 SDK version 17.0.2.
Project Requirement...
I have found a bug in SDK v2.6.0 at zephyr/drivers/flash/nrf_qspi_nor.c while erasing the external MX25R64 flash.
Environment:
nRF5340 DK Hardware (MX25R64 external...
Hi
We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
HW: nRF5340DK NCS: v2.8.0
After installing NCS v2.8.0 from ToolchainManager, I tried to build the project but failed.Error message "No such file or directory: LIBGCC_FILE_NAME...
I have a Raspberry Pi Pico which is powered by a Lipo battery. I want to measure the current with the Power Profiler Kit II. I hooked the 2 grounds to to the board, and VIN...
I am using BLE mesh in nrf52840. I have modified the sensor server sample and sensor client sample to suit my requirements. I am using toolchain and sdk v2.6.1. It is working...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
Hi
For a low power product, I need the nRF54L15 to wake up periodically with very low consumption in between. In the deepest sleep mode there is no RAM retained and so the...
So I've been trying out the nRF9161DK, and had a lot of problems creating builds with the included samples. Mostly CMAKE errors.
Guess I'm missing some basic knowledge here...
As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you
NCS 2.6.0
NRF52840
Hi I am trying to add multiple services to the custom_ble_service tutorial example right now. When I try to create a second ble_cus_t instance 'mcus2' by calling BLE_CUS_DEF...
When I set CONFIG_BT_FIXED_PASSKEY=y in prj.conf. The following warning messages are generated by west build command.
CONFIG_BT_FIXED_PASSKEY is enabled
A fixed passkey...
