Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
I have a BME688 connected to a NRF52840DK and I cannot get a working I2C communication using Zephyr. Below are all sources:
app.overlay
main.c
prj.conf
I was...
Hi.
I am trying to disable the RESET pin (P0.21) on the nRF52810 microcontroller (custom board) and set it up as a normal I/O pin.
I'm using the SDK v2.6.0.
I don't...
Hi, my device is central device( Central UART ) and I couldn't get stable pairing with peripheral device with display which provides passkey code. The scenario: 1. From the...
Following instruction here for setting up NRF52840-Dongle as a radio coprocessor for use with OpenThread Border Router.
The error is at the second step when executing "...
I'm alter the overlay file to adapt my board.
In my board,I try to use pin 9,10 as uart_tx and uart_rx,without cts and rts.
I wirte it in my app.overlay as follow:
...
I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
Hi,
I created a custom board following the instructions from https://www.youtube.com/watch?v=V_dVKgWKILM . Everything is ok and with the "Hello world" example builds without...
Hi,
We have our custom PCB with an nRF9160 SIP that is connected to a nRF9161-DK via P20. I have a couple questions about this setup.
Is it fine for us to program...
Hello,
I want to play a .wav audio file on nRF5340 audio dk.
I convert the wav file into raw data and store it in an array.
After that, I play it using nrfx_i2s_start...
Unable to write to flash memory using direct memory access functions like sd_flash_page_erase & sd_flash_write (nrf52840 nrf SDK 17.1.0) Also attached application and bootloader...
Hi,
I realise this is now quite an old version of the SDK and this particular library is no longer supported, but we have not yet migrated our project (I did try once...
