I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hello
how can i found a input capture example to read external 125KHz PWM Signal, so we can measure the time from falling/falling edge or rising/rising edge or falling/rising...
Hello, from reading devzone, the recommendation for optimal GPS performance while using the nRF9160 DK, is for the antenna to have an unobstructed view of the open sky.
...
Hello,
We have got some devices in the field that run mfw1.3.1 and an application that have some issues with preforming modem FOTA correctly. I'd like to update them to...
Hello,
I have been trying to provision and configure two nodes running Light and the Light_switch examples using a separate node running the mesh provisioner example from...
Hi,
I'm porting an older product that used a Microchip MRF24J40 SPI radio and a PIC processor to an nRF52840 and I'm struggling with how to replicate both the CRC calculations...
Hello,
I am using nRF Connect for VSCode (v2022.7.242) and discovered that the softreset option for a task has no effect.
Task:
Output:
As you can see it is...
Hi All!
I am using a hologram NB-IoT sim card in nrf9160DK. And want to connect it /send data to nrf cloud. I have activated the sim from the hologram website. When I tried...
I bought this device becouse I want to use it as Open Thread Border Router.
I followed the steps on your website: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All:
Good night!
We have 3 pcs of nrf52840-DK and would like to implement and test remote provision functionality with nrfsdk_17.0.2 and nrfsdk_mesh_5.0.
When compiling...
Hi，i'm use latest ncs sdk to develop bluetooth application which use Periodic advertising, when i get started with samples(bluetooth/periodic_adv), and use Ellisys capture...
Hello,
Is AT+COPS manual selection mandatory or just a preference? We have an issue with 9160 choosing a network without PSM if it has better signal quality (when roaming...
Trying to flash devices and getting this error:
make flash
DONE nrf52840_xxaa Flashing: _build/nrf52840_xxaa.hex nrfjprog -f nrf52 --program _build/nrf52840_xxaa.hex ...
Hi,
In our old project we developed low energy sensors based on the Nrf52811 (nrf Connect sdk), using advertisements to broadcast the sensor data, then collecting them with...
Hi
I use the nRF connect SDK v2.0 installed with the toolchain manager and tried the distance measurement which works fine but doesn't use the high precision mode. I changed...
hello Nordic
i am working with zephyr NCS(1.7.1) , with vs code (on manjaro) with the nRF connect extension.
i am looking for a way to map my include files, to find dependencies...
