Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
When I use Windows nRF Connect to connect nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect nRF52832 device. It doesn...
I am trying to implement spi in my project and have encountered an issue where the delay from chipselect to sclk is around 10 us which should be as low as 1us according to...
I have been developing my code on NRF52840 based on nrfsdk v1.7. Since keil free version has a limit of 32kb i am moving my code to VS code. VS by default adds 2.0 latest...
Hi,
I'm testing maximum tx throughput.
I'm using ble_app_hrs example and mcu is nRF52832(s132). (sdk : 16.0.0)
The goal is transmit data at 96Kbps.
I read that the...
Dear Members,
We have 2 ANT receivers and 1 ANT Speed Transmitter, (Bicycle Speed Cadence) , Garmin GSC-10,
Is it possible ? Looks like one receiver gets a good value...
Hi,
I am using NCS v2.0.0, VScode with "nrf connect for vscode v2022.7.242".
I can't build any samples with MCUboot, by enable CONFIG_BOOTLOADER_MCUBOOT =y.
The build...
The following error occurs when I plug in the USB cable to burn the firmware，This is an interesting bug: it usually fails on the first burn, but succeeds on the second or...
Hi everyone,
I am new to nRF52833, and trying to learn it with some tutorials. I am following this tutorial.
You can download my "examples" file from here . You should...
Hi,
Can you please provide some sample code for sending data to Tm4C using ble_app_uart in VScode and also tell me which function I need to use for sending some data from...
When I use Windows nRF Connect to connect to nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect to nRF52832 device. It...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello Groups,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I...
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
