Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
We are currently starting a project with a nordic chip. We want to work with the newest SDK (2.x.x). We saw the new SDK 2.0.0 in the nrf Connect for Desktop Toolchain Manager...
Hi,
Shouldn't the comparability matrix for nrf52833 on package CJAA revision 2 be with a 'J 'not an 'I' for WLCSP
from web site
from product specification: ...
Dear Nordic Engineers
Our customers use the nrf_desktop application to develop their product.
They use the NCS 2.0.0\nrf\applications\nrf_desktop and build project on...
I need to generate a clean 10kHz sine wave. I tried using PWM ( https://devzone.nordicsemi.com/f/nordic-q-a/89209/clarification-on-how-to-generate-a-10khz-sine-wave-with-pwm...
Hello, I followed this tutorial in order to setup custom BLE service. The tutorial as is works correctly and defines one service with an RX write characteristic and a TX notify...
Hi All,
I have implemented sleep mode in the firmware. I am using NRF52833 in my project. When the device is in idle state it goes in sleep mode. I am able to wakeup my...
I tried adding DFU support to my application by following this official tutorial:
But, I get the following errors:
/opt/nordic/ncs/toolchains/v2.0.0/opt/zephyr-sdk...
We're using sd_flash_write() and sd_flash_page_erase() to store some data to internal NOR FLASH at runtime. We have these calls integrated with the RTOS we're using in a HAL...
I've been using nRF Connect for Desktop a lot recently for power measurements with the PPK2 and to program nRF52840Dongles. I keep stumbling over a small missing feature:...
Hello,
I saw in the documentation for the softdevice s132 v5.10 (which is for production use now), I saw it supports changeable MTU. I have searched for the maximum supported...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hi
I have nrf52833DK it was working all fine but suddenly the LED5 is not lighting up and it is not detected by USB port. I tried to check the board voltage regulators and...
Hello,
I just started working on the nRF52 series controller, I want to upgrade my project using BLE features.
I need 1 master device to send to multiple slave devices...
Hi,
According to CryptoCell-312 documentation , it supports the SHA-1 algorithm. I was able to successfully run the SHA-256 cryptography sample application in the nRF Connect...
In my application, I need to use the nrf52840 for both BLE (as the controller) and ShockBurst. Specifically, it's the nrf52840 on the nrf9160 if it matters. I'm using the...
