Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I would like to know if I can update the firmware of modem from 1.1.1 to 1.3.1 on Thingy91 (hardware version 1.4.0).
My goal is to use AGPS and PGPS assistance services...
The product specification states that "o nly the dedicated QSPI pins shall be used. " Is this a recommendation or a requirement? I would like to configure a different pin...
I accidentally closed the original ticket , so I create a new one.
Hi,
recently I'm building dfu function on my board, using nrf51822 qfaa and softdevice s110.
...
hello,
Im using nrf52840 Im trying to emulate a chip select signal for spi slave with gpiote and ppi. I used an active high signal as an event and a signal(cs) that is toggled...
Hi everyone,
I have some questions regarding RSSI:
1. Is there any Bluetooth reference that evaluates the RSSI? For example what RSSI range is considered as perfect, moderate...
env:
SDK: nRF5_SDK_17.0.2_d674dde
KEIL- ARM
SoftDevice： s140_nrf52_7.2.0_softdevice
i can't understand how MBR jump to bootloader, and how MBR konw the start address...
I'm using SDK 17.0.2 and I'm trying to write a small central device. It should connect to a single peripheral and exchange some data.
Once the peripheral is found, central...
Hi,
I am trying to get access to the code 1.99.99-dev1 branch of the NCS, but I'm not sure where I can find this. More specifically, I would like to use the code of the...
Hi.
I am developing a small notification monitor.
It used a 150mha battery and a 0.92 oled.
I want it to be connected to my phone via Bluetooth and when I send a string...
Hello DevZone,
I have a project where I want to use NFCT for communicating and charging. I have used the NRFX_NFCT library to read and write to my transmitter because...
Hi,
I am doing the java programming with BLE advertise, and I want to make BLE advertise events stop when the advertising events number enough. Are there any methods to...
Hello,
for a device I'm developing I need to be able to set values from an App as well as from the device itself (buttons on said device). So far everything works fine...
We are working on ubuntu 18.04 LTS.
We are trying to install nvs package for smart remote 3 microphone activation but got stuck with the package installation as stated in...
