Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hello,
We have an app_timer that runs periodically for the application, and we are also using BLE peripheral code. Once the application timer expires, the event handler...
Hi,
The Dongle was given to me by a colleague of mine who has the exact same laptop as I do. The Dongle was and is working fine with his laptop. The problem is with my office...
Hi ,
i am using nrf52832 soc with customize board trying to optimize the power the following events occur:
1)The first time when i code uploaded it initialize all the...
Hi,
Is there a way to set somewhere in the softdevice or a library to automatically disconnect after an idle connection? Idle means, nog characteristics being read or written...
Dear Nordic,
I have some questions when study the usb audio of nRF52840;
What function when running the nrf_drv_usbd_errata_104 function?
Do I have run it? Can I remove...
Hi,
I am struggling to find a basic sample for UART communication in NCS. As an experienced Nrf5 SDK programmer, I find it very hard to convert my firmware to nRF Connect...
Hi Nordic Support
I have been experimenting with your nRF52840 board there has an SPI flash and have tested it with your USB example that can enumerate the filesystem on...
Hello,
I have the following setup:
a computer connected to a PCA10040 over USB
a PCA10040 connected to a NRF52832 over SWO (SWD IO, SWD CLK, SWO, RESET).
I would...
1. I am using the nrf52832 at the transmission side (ble).
2. at the scanner side I am using the ESP32.
3. I want to display the "advertising device name: " at ESP32 side...
Hi ,
I have been tryiing out the flash_storage example in the SDK /examples/pheripherals/flash_storage . The flash storage , permits us to write hello world to any memory...
Hi There,
I am developing Mesh applications based on Mesh5.0. At present, I have nrd52850DK broads, how can I do to debugger the application? Do I if have a J-link device...
I am not getting how to implement below two points in installation of micro-ecc
Enter the subdirectory for the SoC and the toolchain that you are using to build your application...
Hi Nordric,
In our application we want to receive the sensor data using SPI-DMA and to send processed data on USB.
1. Is it possible to receive sensor data and directly...
Hello,
When I set the tx power in the broadcast initialization, I found that there are restrictions on the setting of the Bluetooth name, as follows
My device name:...
The lNordic Semi Link
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth-LE
mentions that the nRF52840 Dongle can be used as sniffer.
...
