I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
nRF52840DK devicetree describes both uart0 and uart1 explicitly in nrf52840dk_nrf52840.dts file: https://github.com/nrfconnect/sdk-zephyr/blob/v2.3.0-rc1-ncs1/boards/arm/nrf52840dk_nrf52840...
Hello,
NRF52832 - SDK16 - sd132 7.0.1
I have an issue with ble_db_discovery_start() that return NRF_ERROR_NO_MEM, when I followed the functions call I found the error...
Hi,
I started with the Blinky example and have added peer_manager to the project by referencing the hrs example. Everything is building, but on init() I am getting a hard...
I have two custom pcbs containing the nrf52832 chip with the EXACT same hardware and software.
When I program and run the old pcb,
The old pcb runs OK. It returns from...
I use SDK 15.3 and SD S340 v 6.1.1. Bootloader is designed to do custom update through GSM; code based on secure bootloader ble example from SDK. I have used code that previously...
Hi,
Greetings!
We are using following setup
nRF52832 DK
SDK16.0.0
Mesh SDK 4.0.0
Light Switch Server and Client
Here we would like to understand below things...
HI,
I set RTS,CTS to disconnect in the overlay file.
(Toolchain Manager.0.6.1/NCS1.3.0)
&uart0 { rts-pin = <0xFFFFFFFF>; cts-pin = <0xFFFFFFFF>;
};
warnings occur...
Below are the details of my setup configuration:
SDK Version: 11.0.0 (with changes corresponding to hardware)
Soft-device: s130_nrf51_2.0.0
Boot-loader: nrf51422_xxac_s130...
Hi, I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment SDK - nRF5_SDK_16.0.0_98a08e2 ,
IDE - Segger Embedded studio (windows 10 - 64 Bit)...
Hello! I gonna buy a NRF52-DK. The seller says the following about kit version :" Hello, original imported. The latest version of 2020. 2.1.0 version". Is it correct? I can...
Hi
In my application, I use nrf52811 to relay data to make the data go further. If data is sent from point A to point B, point B receives the data and then forwards to...
Hi, I'm currently implementing AGPS on 9160, nrf connect master branch. Right before every GPS search we are connecting to our own server via CoAP. To minimize data usage...
Hi!
Running the Asset-Tracker routine will fail to connect to the cloud(ncs1.3.0). The serial port displays an error say Failed to connect to cloud, error -7.
Error...
