Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We are using the Development boards nRF52-DK from Nordic and trying to utilize the mergehex.exe downloaded from Nordic website.
using Segger Embedded Studio (non commercial...
Sir,
I have one nRF52840 DK and ADXL335 accelerometer. I need to get the 3-axis values, Xout, Yout & Zout, from the accelerometer and send through BLE to my nRF mobile app...
Hi,
I was going through generic_level_messages.h and generic_level_common.h files looking for the parameters for generic level status message.
I noticed that generic_level_messages...
I am using nRF51822 with SDK 10.0. I want to configure a GPIO pin which can wake up the MCU from SYSTEM OFF Mode and call its IRQ handler. Please find below configurations...
Hello,
I am using an nRF52dk with no additional hardware, in conjunction with SEGGER Embedded Studio V4.12. I started with an example from nRF5_SDK_15.3.0_59ac345 called...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I used NRF connect to connect to a slave。
I want to use the central to connect to the device。
this is my code.
but the service is not found。
static void...
We are developing a platform that can have multiple configurations, with or without softdevice/ble, with or without bootloader (for upgrading), both on nrf52832 and nrf52840...
Hello,
I'm using the nRF9160DK (PCA10090 0.8.2). I was able to see the data coming from the nRF9160DK in the nrfcloud, but now I want to be able to see the data published...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hi,
To build the context: I have two peripherals, Sensor 1 and Sensor 2. Sensor 1 has been running off of a NUS service to transmit data. Sensor 2 has been running off of...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi all.
In our project we are using BLE, but at some point switch to ESB. The code below disables the SD, and sets up ESB which is then used from then on.
This all...
Hi,
I am using nRF52 DK PCA10040 to develop an application starting from the ble_app_uart example, Then I introduced PWM and SAADC from other examples, and after I verified...
