Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi ALL,
v2.8.0,NRF54L15DK,I would like to ask：
1. if my pin is P0.00, is nrf_gpio_pin_set(0) correct？
2. If my pin is P1.01, is nrf_gpio_pin_set( 33 ) correct？
Hi,
I would like to flash the ad sample on Nrf54L15-PDK
Flash ends with error messages:
build messages:
I'm I tried running west flash --recover.But it didn...
I have completed a mouse program with 52840, but there are some problems at the moment. On some computers, usb will fail to obtain the descriptor, but there is no problem...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
I am working on custom hardware with an nRF52840. I have added the MCU boot in my earlier development as well but this issue I have never faced before.
Problem statement...
Hi,
iam trying to write the data in nvs which i give input through GATT.i can read and write in nvs when not using gatt,BT.
I have 2 codes,1 is working but without GATT...
Hello,
Board: custom board
Soc: nRF52840
SDK: nRF Connect SDK v2.8.0
I would like to know device mac address and use the mac address in advertsing.
can you please...
This page (v2.8.0) https://docs.nordicsemi.com/bundle/ncs-2.8.0/page/nrf/app_dev/device_guides/fem/fem_nrf21540_gpio_spi.html
Suggests copying the following into devicetree...
I am trying to get std::vector to work on nRF52840 running Zephyr in Visual Studio Code running v2.7.0 toolchain , but have been unable to do so. I found some similar tickets...
Hi nordic
I've try to enable 115200 baud UART on p0.9 and p.10 but I can't make it.
I just saw a thread about 52840 can't use 115200 uart at p0.9, p.10:
https://devzone...
