We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I would like to add a costom cluster,controlled by custom App.I add cluster xml file,and run zap_regen_all.py to generate corresponding code.Everything is ok, the...
I am testing the current consumption of SIM cards with PPK2.
When PPK2 is connected to VCC ( voltage 1.8 v or 3 v ), the PPK2 can display the current properly ( around 9...
Hello I need to read the current mesh IV index of a provisioned node. Found 2 structures with the iv_index field : struct bt_mesh_cdb bt_mesh_cdb and struct bt_mesh_net bt_mesh...
When I package the firmware with nrfutil v7.12.0 version， I pack with a command like this
I got the right app.zip，manifest file
My question is: In nrfutilV7.12.0,...
I am planning to perform encryption using the CC312 accelerator on the nRF5340. I would like to evaluate the power consumption when using the accelerator.
My approach is...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I clone the project from git and try to build the project using custom board but it is giving the cmake error...
1. When adding CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y to the configuration as shown in the diagram, does it enable the use of the CC310 accelerator?
2. My understanding is...
We are making ZigBee product. The base we have took is from nrf connect sdk samples light_switch and coordniator example. everything works fine but we need to keep some information...
"I am working on a project involving Matter over Thread using the nRF52840 development kits. My goal is to pair and communicate between the light_bulb and light_switch Matter...
Dear Devzone,
I'm using 52832，SDK 17.0，keil.
What apis should I call if I want to enter the bootloader mode from my app? For example, I receive a message from a serial...
Hi,
I'm trying to do DFU on a custom designed Bluetooth peripheral device using nrf connect for mobile application. I can able to perform DFU successfully is some mobile...
I am working on RTOS that does not have WiFi driver for nordic wifi chips. I would like to port this driver to that RTOS.
In the documentation there is a mention of platform...
Hello everyone,
I’m facing an issue with step-by-step debugging in VSCode using the ARM GCC compiler with an nRF52811 microcontroller and Nordic’s SDK 17.1.
Here are the...
nRF Connect SDK 2.6.1 + nRF52832
I can't get the execution of shell commands from mcumgr over SMP to work.
Here is my prj.conf :
I registered some custom shell commands...
I have an application I have been developing in NCS v2.3.0. I'm trying now to updata to v2.4.0.
The application targets NRF5340.
It uses NSIB (b0/b0n) and for the application...
