Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
I am getting an error when trying to get a nRF9161 application to connect to a private APN using some PDN configurations.
The error is:
I have not been able to find...
Hello,
I'm working on updating my copy of the nRF Connect SDK from 1.7.0 to 2.4.2. My project runs on an nRF9160 so I had SPM configured for my project and now I need to...
Hi I am working on a NCS v2.6.0 project that is using PSA Crypto to generate a keypair for each device. The keypair is being stored in persistent storage, but the issue I...
Hi Nordic Team,
My project goal is to send sensor data and audio stream from PDM mic over BLE from nRF5340 to another nRF5340 board.
For this I have split the project...
I am working on a new project which will use nRF Connect SDK 2.7.0. In that most of the code will be ported from legacy project that used IAR Embedded Workbench as IDE (Note...
Hello, I am building a Matter application (based on the lightning app) for the nRF7002-DK, and I would like to use part of the Matter SDK that is not included in the example...
Hello,
I have a custom board with an nRF9160 and is running mfw_nrf9160_1.3.5. The design is ready for production so I thought I will build 10 boards first as a pilot run...
I'm attempting to build the aes_gcm sample using NCS 2.4.2 for a custom board with an nRF9160. However, I can just build the project for the nrf9160dk_nrf9160_ns target since...
Dear person in charging,
I would like to know the nrf52833‘s RF power accuracy at the emission power of +8dBm, because it is described on the data sheet that the power accuracy...
Hello
I am new to the NRF Connect and NRF board development. I was trying to run a blinky code on the nrf 52840 dongle using the nrf52840dk. I was referencing the following...
I have a Matter over thread temperature sensor, and low energy consumption is very crucial for me. Therefore, I'm using the Nrf2.7.0 SDK ICD LIT KConfig options and I found...
Hi I am receiving the error "Linking C executable zephyr\zephyr_pre0.elf FAILED:" which I have found is linked to the mcp7940 device tree node through the error code " undefined...
