Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi.
I am experimenting with an internal temperature sensor (TEMP) on an nRF52810 microcontroller and have some questions:
1. How to select a crystal oscillator as a source...
We are developing nRF52840 battery powered device, NCS 2.5.2.
Wanted to use shell for external commands for system testing (currents must be low when the debugger is not...
Hey,
I'm currently working on a legacy project that uses the NRF5 SDK. Rewriting the project to use the nRF Connect SDK would be tedious, time consuming and likely to introduce...
Hello support team,
I have question on how should i setup child image. In my project i need to use hci_rpmsg sample as child image for the bluetooth. However, the current...
Build environment is the nRF SDK Connect for VS Code extension with ncs 2.3.0.
I am trying to accomplish DFU over UART with mcumgr serial console in which primary slot will...
Greetings,
We are trying to enable/implement the read-back protection feature of the nRF52840 SoC and during this process we came accross this reported vulnerability of...
Hi
I am setting up our project to generate a test plan in Bluetooth.com. It is a custom hardware using the nRF52832, so we need to do the RF.PHY-testing.
So in the qualification...
When utilizing PSA crypto, enabling CONFIG_MBEDTLS_LEGACY_CRYPTO_C (such as by turning on OpenThread), the PSA crypto features such as native ITS storage are not functional...
Hi DevZone community, I have an error while building GNSS sample while using SUPL server A-GNSS, please see below the error I get and help me if you know where the issue may...
HI
I want to upload data from the nrf9160 / Thingy:91 to my nrf clound broker.
The upload works fine.
I now want to run a mqtt client on my local dev box ( that is not...
Hi, We have implemented recently the BLE filter accept list based on this sample : https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/bluetooth/peripheral_accept_list...
Hi,
I'm using NRF52832 with SDK11.
In my program i do "sd_power_system_off();"
However, on some units i see arround 50-200uA avarage current and on some units it's even...
I'm having an issue with "west update" taking a very long time on a Windows 11 machine . (Multiple hours) This install of the nRF Connect SDK is just over one month old, and...
Hi,
We are currently working on a project using the nRF5340 and are integrating DFU_OTA (Device Firmware Update Over-The-Air) functionality. Our goal is to implement DFU_OTA...
Hi, in the beginning of development my range of the NRF24+ was around 40 feet. My target was only 6. I have gone thru a lot of PCB revisions and mostly do my testing on the...
