Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I have a working pair of 52840 which transfer data in one direction (at 38Kbps). I want to transfer data in the opposite direction (in lower bitrate), but I find that that...
Hi,
I am using NRF52832. I Have two doubts to clarify about internal flash
1) I have done the flash write of the timestamp in a specific address of internal flash. its...
Hello,
I an using a PWM and sampling 2 ADCs in scan mode. I want to read the output of the PWM as an ADC, kind of like a feedback. Is it possible using PPI.
Thanks
Hi,
I am using an NRF 51 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the ble_peripheral...
Hi Nordic devs,
I guess this is more a suggestion than an issue: The power profiler kit II software, when operating in "Ampere meter" mode has the power switch connected...
When I save the conf file with the following contents and select the corresponding project from `nRF Connect Options`, an error occurs and the project cannot be opened. Please...
Hello, I'm trying to port my working project from 52811 to 52832 Both are on SDK 16.0.0, SD 7.0.1 Here is the advertising code that works on 52811 :
This code crashes on...
Hello!
I'm tinkering with the NCS libraries, and I'm really liking the way this is turning out coming from the nRF5 SDK! My question is what is the best practice for creating...
Hello,
I am a newbie and trying to setup nordic thingy 91. I have booted the updated version of modem firm ware and also the "thingy91_nbiot_2020-10-30_5522ca2b.hex" file...
Hi Community!
I'm working on product development for a client/customer. The product will be a small embedded system with an LTE chip (nRF9160) and a BLE chip (nrf52840)...
I'm having a lot of confusion with using TWI on this chip. I have been running example code that I found in this tutorial nRF5 SDK - Tutorial for Beginners Pt 35 B - TWI ...
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-1-ncs-v1-4-0 I follow the link above to create a hello world project, which has failed all the time. Here is the...
SDK16.0.0 + Mesh SDK 4.1.0
Help, we have developed our own board with a Fanstel BT840X module. Some of our boards are asserting ("Softdevice assert: 154516:0") and I am...
Hi Nordic,
I'm using nRF52 DK (PCA10040). I tried to copy and paste the project from this default location:
...\nRF5_SDK_17.0.2_d674dde\example\peripheral\twi_sensor ...
Hi,
I managed to compile and run(?) my first two programs for nrf51 dongle on Keil uVision, however while i think they run I cannot make the debugger work and see what they...
