Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I‘m a rookie for the matter.I use nrf52840 In the matter lock case,when i press button 4,it will start adv.But it did't start.
so i want to add config log to debug,But...
I am attempting to stream data in chunks of 65535 bytes from the nRF9160 using data mode from the 2.6.1 version of serial_lte_modem sample code. The nRF9160 receives AT commands...
I followed the MacOS command line installation instructions at docs.nordicsemi.com/.../install_ncs.html
After running `west update`, it says the tree structure should be...
When following instructions for setting up the NRF52840-dongle as RCP coprocessor , I'm getting this error: ModuleNotFoundError: No module named 'intelhex'
Full log...
I have some initial questions regarding the nPM1300 :) :
- It is possible to download the nPM1300 datasheet as a PDF file instead of viewing it online?
- Regarding VBUS...
When I do a sd_ble_gattc_char_value_by_uuid_read I can only get a maximum of 253 bytes.
And when I read more I get a gatt_status of
BLE_GATT_STATUS_ATTERR_INVALID 0x0100...
when testing NIDD on NRF9151 we are using sock connect -f packet -t raw but it is giving us error
mosh:~$ > sock connect -f packet -t raw sock connect -f packet -t raw Socket...
I want to use RTC in my project. I'm facing build issue (undefined reference to `__device_dts_ord_113') in my project .
STEPS TAKEN: 1. I have enabled the RTC configuration...
Hello everyone.
I am going to do a project recently. We are using dht22 to transmit temperature and humidity, and use temperature values to control LEDs.
This project...
Hello, and thanks for reading. We are having some problems with our device, and hope someone here has the missing piece of wisdom we need. Our device implements HID over GATT...
So in our factory I had setup both an nRF51-DK (PCA10028) and nRF52-DK (PCA10040) to program our external boards we are producing which has a NRF51822-QFAB-R7 populated on...
Hi,
My custom board uses Raytac MDBT53v, which has nRF5340 as its MCU.
My SW is based on the example audio code, and I want to use my external NOR FLAH IC (Macronix MX25R6435F...
Hello,
I am finishing the development of a device based on the nrf52810. When the device is connected to a central, I would like to periodically measure the voltage on VDD...
Hi, I am working on a Bluetooth Mesh project for lighting control using nRF5340. I am currently stuck on how to implement a Bluetooth Mesh gateway for my mesh network. Here...
Hi everyone,
I'm currently working on a project involving an Ember ZigBee end device and a Nordic ZigBee coordinator ( Nordic nRF52840 donngle) . I’ve encountered an issue...
