Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
My goal is to achieve a...
Hi Everyone, I'm trying to pair the nano leaf bulb using matter chip tool via Open thread border router. I need some help on how to use chip tool to commision the matter device...
Hi,
I want to weld my product that contains NRF52840, using an ultrasonic welding machine.
Currently I'm thinking of a welding frequency of 20KHz or 40KHz.
1. Is there...
I am currently working on a NINA-B4-TAG from ublox, there is a requirement to be able to dynamically turn on and off the CTE without completely turning the advertising off...
I am thinking of using nRF5340 Audio on a development board.
The I2S-compatible IC on the headset side is an IC called AK4432VT.
The following settings are required to...
Hi,
We have a nrf5340 module on a custom PCB that is connected to a computer through use of a pcie header. This PCIE header allows USB communication to the module and supplies...
Hi,
In my project I need to send maximum bytes possible inside one package. When using the nrf connect app I can see that when reading the characteristic this works, but...
Hi . I have two questions about the PIPEs in Zephyr RTOS , especially regarding the correct use of the k _pipe _put and k _pipe _get functions :
1 ) In both functions ,...
Hi,
when I configure CONFIG_BT_SETTINGS=y as I want the device to remember the pairing parameters, the services defined with BT_GATT_SERVICE_DEFINE dissapear.
As far as...
Hi,
I use nrf52833 running ncsv2.6.0,
I trans v2.6.0\nrf\samples\bluetooth\central_hids to \ncs_v2.6.0\v2.6.0\zephyr\samples\subsys\usb\hid and now plus usb to nrfUSB...
How do I switch nrf52832 from a broadcaster to a peripheral with a service via a keystroke interrupt? After trying it out, I found that my problem was mainly: I didn't know...
Hi,
I'm trying to control nrf9160 SIP from stm32 MCU via AT Commands. Should I program on the nrf9160 the AT_CLIENT sample for this purpose or is not neccesary?
I'm trying...
Hello Team, We are currently working on a project for interfacing Larger TFT LCD display with Capacitive touch with nRF5340 Devkit board and SoC. As per the datasheet of the...
We use custom board with NRF52840 and a MODBUS CO2 sensor. We are struggling with power consumption when the serial is enabled. The goal is to take measurements and then put...
