Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
Hello,
I do not see a SWO (Single Wire Output) pin on this package. The regular size package has this function on P0.18 but not on the WLCSP package.
Please advise.
...
Hi,
I have several devices with the RIGADO BMDWare on them but whose hardware is inaccessible. I want to initialize these nRF52832 chips with out nRF Bootloader, Softdevice...
hi
I use nrf52840 with SDK17.1.
1.How to DFU via ble combined uart in the same application?I have sdudied a few of tickets ,example https://devzone.nordicsemi.com/f/nordic...
Hi all:
We are developing mesh project using nrf52833 based on mesh sdk 5.0. First the nrf52833 device can be sucessfully provisioned into a mesh node using mesh lpn example...
Hi, I am a beginner developer who is developing a product using nrf52832(s131). An issue arises and asks a question.
I hope to do infinite scanning and advertising, whether...
Hi，
On the nRF5_SDK_for_Zigbee_v3.2.0 version, it is found that when the device loses contact with the parent node, the node becomes a factory new device; if you want to...
Hi,
I was creating a struct called ch201_device. So below is the code initialization.
and in the c code, I create a function for that use a method from ch201_device...
The chip I am using is the nRF24L01.
Not the nRF24L01 P .
One module is Rx-receiver and two modules are Tx-transmitter.
The test is carried out with one Rx module and...
hello,everyone! I'm having a major problem with my nrf9160 dk board suddenly not connecting to the cloud. I registered and renewed my certificate, but the result still failed...
Hi:
There is no driver on win7 using nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd_ble_uart example.
I tried to use nRF5_SDK_17.1.0_ddde560\examples\usb_drivers, but...
Hi,
I am develloping a solution with an extended advertising.
In order to see the advertising, I am using either the nrf connect mobile APP, either Nrf Connect Desktop...
Dear Support Team，
Based on SDK15.3, nRF52832, follow the instructions to run the DFU process, use the mergehex.exe tool to merge settings, app, boot, and sd into one hex...
