Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I'm using ble_app_uart to test AT.
When I sending a buffer
reset_buff[10]="AT+RESET\r\n";
RTT log showing an error
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at...
Hi all,
I'm currently trying to interface an nRF52832 with an external Flash chip via SPI
I have tried with both NAND and NOR types, specifically the MT29F2G01 from Micron...
I am trying to develop CAN communication using nRF52 dev kit based on nRF52832 (PCA10040) and a MIKROE CAN SPI click 3.3V board . This board has an mcp2515 stand alone CAN...
Hello,
I had RTT configured as the logging backend and it was working fine. When I enabled the SHELL on RTT, the log output stopped. Maybe more specifically, printk() output...
Hello there,
I'm trying to downgrade nRF Programmer from v2.0.0 to v1.4.11 as it is not possible anymore to select a Segger debugger as target device in the newer version...
Im trying to make a simpel project reading the sensor BME280 over SPI. I can´t get any activity on the SPI pins when i check with my logic analyzer.
I´m using nrf9160-DK...
I've based my code upon the HIDS keyboard example and added code to support an attached polled sensor with I2C interface. The device will pair with the Android phone just...
Hello,
I'm writing an application that sends cycling power information via ANT+ and Bluetooth (S340, on a nRF82840). While the ANT+ is a pure cycling power service, the...
Hello,
I am using the Nordic SDK at v1.5.0, to create an application that runs on the Nordic nRF9160.
In the typical use case scenario, my application is mains powered...
Hello. 'm trying to DFU using serial bootloader with my custom board.
I've wired my custom board's nrf52833 pin with a USB2UART board.
nrf52833 RX Pin: P1.02 -- connected...
We have a device based on NRF52832, SDK 13.0, Softdevice S132 v4.0.5. We can't upgrade the Softdevice at this time but we can modify the firmware if necessary.
We know that...
My current product uses an NRF52832 with SDK 13.0 and s132_nrf52_4.0.5
I was asked to implement GATT caching to speed up the connection time with a mobile phone.
I know...
Dear ALL,
In nrf connect sdk ，How can I do a bond_ Deleted callback？At present, I test this function in iPhone and Android OS. When I delete the pairing information of...
I am developing my ADC sampling code for minimal power consumption. There is a timer with ppi module that generates interrupt for sampling. Please see the code below:
...
