We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
nRF51 RTX 4.74.0-3
SoftDevice S210 V4.0.1-3
Created a timer for 5 seconds interval.
It turned to be 4.4 seconds. with or without softdevice enabled.
Anybody else has...
Hi,
Access to the UART hangs the execution of the experimental_ble_app_uart_s110_pca10028 example.
The phenomen occures In the file simple_uart.c when checking for the...
This may not be a major disaster,but it bothers me:
I have written an application to read data from an ADXL345 accelerometer (using SPI) and print out the data on a console...
Good morning,
i still couldnt find out if it is possible or recommended to use the PPI together with the s110. i checked the example in the sdk documentation but it was...
I have an in memory log variable that I write to on various BLE and device manager events. If there is ever a serious error, my implementation of app_error_handler() now takes...
Hi,
I have programmed the radio_test_example to target having nrf51822 qfacaa chip. I have changed the UART pins as per the custom board.
It's working fine but showing...
Hi,
How can i wake up(interrupt) the nrf51822 device from "air" (from my iPhone application)?
For example after i paired iphone with nrf51822 i want to put the nrf to sleep...
I am using SDK 7.1 and I am attempting to use the Makefile.common found in sdk_7.1->components->toolchain->gcc->Makefile.common. However, the Makefile.common appears to contain...
I'm trying to send multiple 20byte notifications per interval through the NUS usart service to iOS 7.0, 30ms conn. interval in the UART demo app. It seems I cannot tx more...
Hello,
I'm working on a project with SoftDevice s120. I played with the project ble_app_multilink_central. The maximum number of characteristics per service supported by...
Our application includes a 32.768 kHz crystal oscillator with a nominal +/- 20 PPM accuracy. When I factor in aging over 10 years and worst case variation due to temperature...
Hi !
In questions question1 & question2 Petter Myhre gave a complete answers about count of max characteristic per service in s120 and how to resolve this restriction....
Hi,
I am now developing the BLE with our company's own sensor, so we are not using the motherboard. There always a problem when we use it. I am using the PCA10004 board and...
SourceCode_SSDI_BTLE_BeaconReceiver.zip I am starting to use the Nordic chips, and have a PCA10004 board running. I have modified the experimental_ble_app_multiactivity_beacon...
Hi Nordic,
I am a hardware/firmware guy without App development skills and I also lack the time to acquire these skills. I enjoyed your UART App during my development,...
