Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am looking to do some testing with nuSIM. Monogoto has provided the sim profile but they say we need to obtain the SIM number from Nordic directly.
I was unable to find...
Hi, since the Nrf5340 has two identical Cortex-M33 cores, I was wondering whether it would be possible to enable the trustzone for both cores, and if yes, how. Thanks.
Hello!
We are working on a custom PCB with nrf54l15 chip on nrf connect sdk version 3.2.0.
The I2C (TWIM) SCL line functions correctly, but the SDA line is not being driven...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
Hi，
During full-device testing, we observed that two devices encounter the MPSL ASSERT: 1, 1519 error after approximately one hour of operation, which causes the MCU to...
Hi Nordic,
On the NCS3.0.2+NRF54L15 platform, we intend to generate pulse widths by controlling P2.1 and P2.5 through timer+PPI. Originally, we planned to use PPI for operation...
Hello,
I have a problem with a tablet that i was planning on using (Xiaomi Pad Pro), my device (nrf25840 dk) is sending data in packets, 4000bytes per packet and its sending...
Hello,
I am working on a custom product based on the nRF9151. I am currently learning RF testing methodologies and setting up a verification plan.
I have read the HW...
Dear all,
I am trying to build bluetooth hci controller for Home Assistant.
I used official example for create usb bluetooth hci controller here:
~/ncs/v3.2.0/zephyr...
Using the options described in ncs documentation for one image pair updates (i.e. not multi-image DFU) appears to be broken in ncs 3.0 and later for upgrading the network...
Hi all,
I'm working with the nRF54L and encountering persistent SAADC issues after short deep sleep cycles.
Setup:
SAADC is configured in differential mode with oversampling...
Issue
When building the Blinky example for the NRF54LM20A with TFM and CONFIG_DEBUG=y the MCU will assert on boot.
When booting an assert is triggered in workspace/modules...
Hello,
I have been developing on a nRF9151DK v0.9.0 for a few weeks now. So far this board is great! However, I have been running some long duration tests recently and logging...
hello, We have a project that uses sound for distance measurement.
When I upgraded from NCSv3.0.0 to NCSv3.2.1, I encountered a problem where the i2s function stopped working...
