Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
hi support team,
customer is ordering sims from network supplier, and i got one sim card, but after testing i found this sim card can't be recognized.
here is the modem...
Hi
We have developed a remote-control system where both the sender and receiver are built around nRF52840. Today, the SDK is sdk-17.1.0. We are now considering moving over...
Hi Nordic Team,
I would like to use a USB camera in my project with the nRF5340. Is this possible? If so, could you please share any reference documentation or example links...
Hello all,
I am currently using the nRF9160 DK for cellular uplink to our server for an evaluation. From the nRF connect software I use the provided firmware 'AT Host' and...
Hi Team,
I'm working on an application using the nRF5340 , and I'm implementing a low power mode in which the system shuts down non-essential peripherals and aborts all...
Ncs v3.2.1 <SDK>\nrf\samples\dfu\single_slot
I want to try using this sample for SMP over ble dfu, so I tried several times in the nRF Connect and Device Manager in the...
Hello,
I couldn't find any related certification reports on the product page of the nRF52840-QIAA-R.
May I ask if this chip has IEC, 3C, or UL certification?
BR,
Hi,
We are making the module having NRF54L15 bluetooth and NRF21540 AFE chip.
now can we use Channel sounding feature on dual antenna or single antenna with NRF54L15 ...
Hello,
We are currently developing a project based on the nRF52832 SoC, where two external sensors are connected:
Proximity Sensor: VCNL4040
Accelerometer: LIS2DH...
Hi
I was initially using Window 10 Laptop with nrf52832 ncs2.9.0 in visual studio code....I developed a ble application with mcuboot (over ble - reference nrf academy tutorials...
Hi,
1. The customer has two projects that both require the use of mcuboot. However, for these two projects, the source code and configuration of mcuboot need to be modified...
Hi, I'm working on a custom board with the nRF54L15 using NCS 3.2.1, and have configured spi21 on port 2 for a display. SPI pin configuration: SCK: P2.06 (TRACECLK) CS: P2...
I am working my way through the DevAcadmy (nRF Connect SDK Fundamentals) using an nRF52840 development kit.
In lesson 6, exercise 1, I try to get an I2C with a BME280 to...
