Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
We are working on an nrf54l15dk board but want to log directly to the nrf flash memory (instead of the ext flash) - which we are doing successfully. In Zephyr we have logging...
I am trying to create a L2CAP CoC between a nRF52840 SoC using nRF5 SDK version 15.3.0 and a Pixel 3 XL running Android 12 without the use of GATT. Currently I use GAP for...
I'm currently trying to port some software to the nrf52840 dongle, and it works great, if I do not activate NVS.
As soon as I activate NVS, then the dongle shows no lifesigns...
Hi,
in https://github.com/nrfconnect/sdk-zephyr/blob/ncs-v3.2.0/lib/os/clock.c i think an include to properly resolve CLOCK_REALTIME or
CLOCK_MONOTONIC is missing, if...
I’m working on a prototype based on the nRF5340 Audio DK, starting from the included nrf5340_audio application (NCS v3.1.1). The goal is to support multiple simultaneous Bluetooth...
Hello,
I would like to ask about LTE-M communication latency when using nRF9151-DK. I am using a TCP connection to transfer data read from another device via UART (MTU=1500...
Hello! Has anyone been able to get the LED Strip samplee code and consequently drivers to work with NRF54 Dev Kit? I have tried copying .overlay from NRF53 but can't get the...
I have been reviewing the datasheet of the BLE audio SoC nRF5340. The ADC sampling frequency is mentioned, but the rate is not specified.
he references voltage is specified...
Hello,
I am trying to get the RSSI value of a connected device on the nRF54L15, the same thing with our nrf54H20 device (nRF54H20 would be great if i can retrieve it via...
I am curious about the RF pin impedance, as this parameter is not listed in the relevant specification for nRF54 SoC family (i.e. datasheet v1.0).
I wonder whether it is...
Hi,
To improve the accuracy of RTT-based ranging measurements, the Bluetooth CS specifications requires that the initiator compensate for the fractional frequency offset...
We are using QSPI to connect nrf52840 DK with nand flash of AS5F34G04SND. In page 28, 29, and page 17-table 2-1 of datasheet of the flash, we need to Program load x4 IO: sending...
I am on a custom NRF54L15 module where I want to change the default UART TX pin from P1.04 to P2.07. Unfortunately, there is no output. Using P1.14 somehow works? I also have...
Using nrf connect 3.1.1
using nrf54L15 evaluation board.
Hi,
I have an application that is using the shell capabilities of the zephyr. uart and shell is connected...
