Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi
I have some questions regarding the 32 MHz crystal on the nRF54L15:
If my firmware is configured to use external capacitors, will the very first crystal startup...
Hi,
I am developing on nRF54L15-DK BM (bare metal) for another board with a different pinout.
I need to disable the the MCUMGR log that prints to UART TX pin 1. 04....
Hi,
I am working on Google fast pair locator tag using NCS sample code. For final product, we need one function in device for certification that is to disable and reenable...
Hi nordic support:
Our product used nRF52840, we tried test nRF52840's BLE OTA RF performance with CMW500. After the nRF52840 device is assembled with the casing, it is...
We have a custom nRF5340 board that interfaces with an MT29 NAND Flash IC over the SPIM3 peripheral. Our DFU solution involves storing update and rollback images on this external...
I'm developing on the nRF54L15-DK using NCS3.1.1. I've recently encountered a strange behavior.
My program writes to the RESETREAS register. A bus fault sometimes occurs...
Hello,
Following the ongoing many issues to make Ethernet work alongside the modem on nRF9160 ( , , devzone.nordicsemi.com/.../ (clicking “Convert to public” on this one...
Hi !
I've been through a lot of documentation but did not find any matching my case.
I'm using a custom board with an NRF9160 chosen for its ability to connect to LTE...
Hello,
I want to use P0.10 and P0.11 for SPI purpose for my custom nrf5340 board.
But when I clear the forwarder property for these pins from the pin editor gui, I am...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hi Support:
I am testing channel sounding initiator on our board, but there is a crash on CS initiator starting.
below is log:
uart:~$ initiator on [00:57:24.604,598...
Hello,
The Altium lib provided with the DK, has two geometries, one with an "_2" at the end, what is the difference between these? (if any).
Thank you,
Beleni...
Hello,
I’m using the aws_iot sample with the nRF9160DK-nRF9160 target. When I introduce a bug (calling `net_if_up()` on a wrong interface), the system crashes and halts...
