Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Do you have an example of how to add the adxl367 accelerometer to the asset tracker sample template.
I would like to use the accelerometer to detect movement beyond a defined...
Hi Nordic team, I’m working on the nRF54L15 DK with the SAADC peripheral and have encountered an issue when enabling noise shaping.
Here’s the setup:
Platform: nRF54L15...
My ncs version is v3.1.1 and I'm trying to connect a chip (INTAN)RHD2164 using SPI on the nRF54L15 DK. The special feature is that it needs to sample data at double the rate...
Hi. I'm working on a code that performs an action and immediately goes into System OFF mode. Before that, it configures GRTC as a wake-up source with a 5 secs timeout. I've...
Hello, I designed a new custom PCB with nRF52832 and I would like to ask you for verification.
I have the MCU and some components regarding Battery Management.
The idea...
Hello,
in my application I use SPI communication to control my display. For that I have configured the pins for spi4 in the dts and all works fine.
Now I would like...
Question:
What's the maximum NRF_SDH_BLE_GATT_MAX_MTU_SIZE supported by S113 v7.2.0 on nRF52833?
Current setup:
Chip: nRF52833
SoftDevice: S113 v7.2.0
...
I am following the nRF Connect SDK Academy, Lesson 1, Exercise 2 on a Windows 11 system. I got to step 4.12, "Click the build configuration button." After running for some...
Hello,
The MPLAB Snap debugger says that it supports "Cortex SWD". Can I use this to program an NRF54L15? Ideally I'd build the program in nordic vs code and then take...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). I am using a custom board. Below is the configuration I set in .overlay file
And below...
We would like to reset or factory reset or initial flashing of nrf52840dk? We tried pressing RESET button during power cycle, but did not worked. Let us know your thoughts...
Hi,
I'm designing a battery-powered device using the nPM1304 PMIC and nRF54L15. I want to implement a sleep/wake function using a single button.
Desired behavior:
...
This has been resolved, but resolving this issue took quite a bit effort: I was wondering why my NFC was not working on my custom board. First I thought it would be an antenna...
Hi Nordic Support,
I’m designing a product with the nPM2100 using NiMH batteries .
I know the fuel gauge feature is designed for primary cells and lacks hardware coulomb...
Hi,
The Bluetooth Channel Sounding specification empowers every compatible device (like the new nRF54L series devices) to be a mini radar actually. The Bluetooth Channel...
