My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
I’m working on a distributed testing pipeline where tests are built on one machine, but executed on a separate, lightweight container that does not contain the full...
Hello Nordic Team and Community,
I'm working on a fully automated Zephyr RTOS development environment on Raspberry Pi (Debian Bookworm) targeted at the nRF52840 Dongle....
Hello,
Is it possible to get logs (RTT) from an application started by a bootloader? As of now I don't get anything after the bootloader has jumped to the application start...
While running the BLE HCI USB ( bluetooth_hci_usb ) sample in Raw mode on an nRF52840 board, we observe a bus fault under specific conditions. The fault occurs when the device...
Hello everybody,
I am a research assistant at a university , responsible for maintaining and porting existing student lab exercises from the legacy nRF5 SDK to the nRF Connect...
Background:
My project is using the nrf54L15 with the 48 pin package. I'm using vscode with v3.2.0. The QFN48 package has the following pins bonded from the silicon to the...
I am trying to receive extended advertising from a device on nRF52832 .
I have made the following changes:
sdk_config
# define NRF_BLE_SCAN_BUFFER BLE_GAP_SCAN_BUFFER_EXTENDED_MIN...
Hello
Is there a possibility to build MCUBoot, SoftDevice, Firmware Loader and Application separately and then merge it manually? Or to build MCUboot + SoftDevice + Firmware...
Hello there,
I am working on a project which involves nRF52840 to scan and connect to specific BLE beacon.
So while scanning, nRF writes scanned data on UART. On same...
Hello,
I'm running SDK v.2.8.0 and developing using the nRF5340 Audio DK. I've successfully flashed using the buildprog.py script, and have set up my DK as an Auracast source...
Hi
1. At nRF5340 datasheet page 420, the PDM duty cycle is 40%~60%, any register can tune duty cycle? Or it's nRF5340 variation tolerance?
2. Since our DMIC IM69D128S...
Hi all,
I'm testing Skylo NTN on nRF9151 SMA DK with the latest pre-commercial/alpha NTN modem firmware (downloaded mid-December 2025).
Registration works fine, and uplink...
I am trying to get the nrf/sampoles/bluetooth/direct_test_mode working together with the code from zephyr/samples/subsys/usb/dfu-next.
I have the DTM mode running correctly...
