Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello!
We are planning on using the nRF52832 DK together with an external antenna. We are highly interested in the readings being as accurate as possible, and we are wondering...
We are developing an application in which we need to modify an existing device driver. It's about LIS2DH driver that is part of nRF Connect SDK v1.8.0 and we are using VSCode...
Hi, we are using the nRF52 DK (nRF52832) to read data from the i2s bus and store it as a wave-file on the connected SD-Card. When pressing button 1 on the DK, recording starts...
(For some reason, I use "...' replace the original string) Here is the log for using AT to do HTTPS POST:
2022-02-07T12:19:39.057Z DEBUG modem >> AT#XHTTPCCON=1,"...",443...
Hi,
I'm working with NRF Connect SDK, and once in a while when I add new configuration options to the prj.conf, I get an error that some region overflowed by X bytes,...
Dear friend,
Since the customized nRF5340 board does not have an external 32.768KHz low-frequency crystal oscillator, the following is added to prj.conf in netboot:
The...
Hi
This is the first time I have tried to use the nrf52840 dongle and the programmer v2.3.1, it can see the dongle( com10), but as soon as I select Device tis is the response...
I facing a problem. When, progrsmis run for testing on nRF5340DK using SES, the CPU resets automaticaly. The RAM does not respond timely is shown , please see the attached...
Hi everyone,
There is an open ticket that I need support with because the responsible engineer will be out of the office until the new year.
In a nutshell:
I design...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Please tell me about "nrf_sdh_enable_request". This API only makes a request, so I understand that the SoftDevice...
Hello Respected members, I hope this post finds you well. Can someone help me with how to store UART data in FLASH? The Idea is that I have to send the Date Or Serial Number...
Hello !
As part of nrf_crypto it is no any examples how-to use chacha20 without poly e.g only stream cipher.
Would be nice to use it via nrf_crypto and evaluate hw accelerated...
Hello. I had worked on nrf52840 development kit with BLE UART code(pin 6 and 8 as Tx and Rx). I used the same code on Fanstel EV BC840M board. I changed the Uart pins to 9...
