Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
The initialized struct "nrf_fstorage_t" for use in nrf_fstorage_init( ) temporarily includes the application and bootloader (just for this test)
start address is 0x2'600...
Hi,
I have setup a provisionner with the sdk example that can provision devices. For that the provisioner scan unprovisioned devices and can start a provisioning process...
Hello,
I am trying to see how the signal strength for Zigbee and BLE changes when the distance between two nR5340 DK increases.
I used central_uart and peripheral_uart...
Although my Googling skills are not the best I have, so far, been unable to find any examples or driver documentation for the comparator peripheral of the nRF52840 for the...
I'm using the asset_tracker app on a custom board and have built 50 of the custom boards. All but one of them start the modem and listen to the LTE receiver for a full minute...
Hello, I followed getting starting guide, and got SDK and tools installed for nRF52-DK, I'm trying to open, build and run some examples. But when trying to open any example...
Hi.
I am using nRF52840 dongle and running saadc example on it.
To print the ADC data buffer "p_event->data.done.p_buffer" in PC, I am using USB_CDC. The size of SAMPLES_IN_BUFFER...
I have implemented the custom service and added custom characteristics following the tutorial series, now I can connect and see the characteristics and their values. I can...
My NRF52DK (PCA10040) J-Link always shows SWD speed 1000 kHz, even if I set the speed to 2000 or 4000 kHz. Is it not possible to connect at higher speeds?
I was working with "Debug configuration" for my nrf board on Segger Embedded Studio. It was working perfectly. But when I changed it to "Release configuration", It doesn't...
Hi everyone,
I am using nrf52840 and I want to change the advertising name in bootloader from "DFUTarg" to a custom name on application side.
For unbonded one, I saw...
Hi,
I'm using the provisioning example from the mesh sdk and I have an "ASSERTION FAILED at :0" error when I'm trying to re provision a node that I have provision before...
Hi
I try to understand where does the interrupt proirity for UART is set.
I see that uarte_1_init() is called from uart_nrfx_uarte.c.
uarte_1_init() is declared from...
Hello I am using sdk v17.0.2.
I found a problem with Bluetooth connection while using 'ble_nus_data_send()'.
the system will stop if disconnect the Bluetooth while transferring...
