My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hello
i have a design limitation for height in my product and i need to find another inductor with a max height of ~0.5mm can you please share more information regarding...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
I am in the process of migrating an existing project from 2020 to the newest version of Zephy/Nordic. I am having issues with the I2C bus. I created a test project using the...
Hello, I'm trying to connect my nrf7002dk board to wifi with Zephyr. I'm using this sample : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/wifi/sta/README...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2). I see that with this example the boot time of the...
I am using the nRF54L15 and NCS SDK v3.0.2 in my project. I need to wake up the board via interrupts from a pressure sensor and a gyro sensor.
The GPIO requirements are...
Hello
I compiled the zephyr example ../zephyr/samples/drivers/i2s/output
The SCK and MCK Signal do have both the same frequency. The bit positioin on MSB in not in the...
Hi there,
This is a follow up post from my earlier one here about using nRF5340 dk as an I2S master for the purpose of recording sound using a MEMS sensor ICS43434. Here...
I’m implementing static passkey security in a BLE peripheral using nRF52810 with SDK 17.1.0. I have added a feature where the device disconnects automatically if the user...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
Hello,
I am trying to get confirmation regarding if I should expect to receive DeviceShadow events through the nRF Message Routing Service.
https://docs.nordicsemi.com...
Hi.
I made the smallest system module using nRF52840. The schematic diagram is as follows.
My reference design for power supply is as follows,
For Firmware....
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
I am using nrf5340 audio dk, v3.0.2 SDK. I added CONFIG_BT_TINYCRYPT_ECC=n in prj.conf and got this error: C:/ncs/bumble/hci_uart_0806/prj.conf:23: warning: attempt to assign...
