Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
I purchased my first nordic semiconductors device, the PPKII, from Farnell.
I just received it today and installed the required software (nRF Connect on macOS...
Hello, I'm using Fanstel's BT840X that includes a SKY66112 front end. It works great with the FEM module in NRF Connect SDK. My problem is that my device has the option to...
We are using nRF54L15 with Zephyr + (NCS) for a low-power application.
Our firmware performs the following cycle repeatedly:
Wake up from System OFF
Perform...
Hi,
We found a weird case that when we re-populate the definition of SPI-NOR flash
- From original pin (gpio0.8/9/10, U15 populated on NRF7002DK)
- To pins (gpio1...
Hello Nordic Team,
I am implementing OTA in a pairing and bonding-enabled application, but I am facing an issue during the ZIP file upload. Additionally, the graph is...
Hello,
I'm working with the nRF9151, and I want to get useful information when a NULL pointer dereference happens, as I am used to on other devices. However, when a NULL...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Hi everyone,
I am currently working with Circuit Dojo nRF9151 using nRF Connect SDK v3.0.1.
When measuring power consumption over MQTT and UDP , i noticed ~25mA every...
When I wake up from sys_poweroff using GRTC, the reset cause I get is reset_clock which is defined as clock error. I am supposed to be waking up with reset cause
RESET_LOW_POWER_WAKE...
HI,
I am using the nRF54L15 + nRF21540 with SDK v3.2.1 , and performing custom development based on the periodic_adv_conn sample.
issue Description
During runtime...
Hi,
A few months ago, I raised a ticket regarding the integration of SoftSIM into the nrf_cloud_multi_service sample. With the help of one of your support engineers, I was...
There appears to be a bug with commenting in prj.conf. If I do this:
# This is the appearance of the device from the BLE SIG Assigned Numbers List (384 is general remote...
Hi,
I'm designing a custom board with the nRF9151, nRF54L15, and nRF7000. I've read in several places that the SPI bus used by the nRF70 series should not be shared with...
Hello,
I configured the hci_uart sample for the nRF54L15 DK by following the instructions in this official Nordic documentation:
https://docs.nordicsemi.com/bundle...
I have an additional part in my design that requires a 32MHz clock input. Is there a 32MHz buffered clock output that can be configured/used from the nRF54/nPM1300 to achieve...
