Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello, I'm trying to map custom PIN mapping on my prototype board, based on nRF9160 DK. I had to remove the UART0 pins and map them for my purpose, but when I'm trying to...
In nRF SDK 1.2.0 and 1.3.0, there is a function to generate the public/private RSA keys in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrfxlib/nrf_security...
I want to develop the tool to download the firmware，so，I need to call the interface of nrfjprog.dll，but there aren·t the detailed descreption，who can teach me？
Question...
Hello, I am working on bare-metal with the BSDLib on a custom board. When trying to debug a specific case in which our server refuses TLS connection, I wanted to see which...
Dear all; I am an originally signal processing expert working on "positioning in smart cities" for IoT using bluetooth 5.1. As part of our new tasks, we are to evaluate the...
I have several nrf52832 based (similar) devices, all are programmed once (at least), now when i try to update program some of devices cannot be programmed (about 5...10% of...
we make the tracking system. so, we want to measure the voltage of li-po battery (i am using nrf51 sensor tag with li-po battery), so, their is any circuitry or any API or...
Hi!
Program enters infinite loop in `sd_ble_gap_adv_start`.
Setup: I've seen https://devzone.nordicsemi.com/f/nordic-q-a/11818/sd_ble_gap_adv_start-hangs-after-disconnect...
Hello,
I've been trying to get a Thingy:91 to connect to the nRF Cloud from Shenzhen, China.
The modem is updated to mfwnrf9160120 and the firmware is on thingy91_nbiot_dfu_2020...
Hello,
I Have a custom PCB with Fanstel BT832 module soldered. Because that module does not have a 32 KHz quartz I need to set use the internal RC source instead. The problem...
Hello,
I am trying to understand if I am able to use the SPI pins as GPIO when SPI is not being used. This post says that we could be able to use I2C and SPI pins besides...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
am use SPIM . I...
I have an issue in buttonless dfu,I have 2 kinds of device,one has issue in dfu,another one has buttonless dfu and works well, I transported DFU code form another kind of...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am in the process of RF certification.
I downloaded the example at "nRF5_SDK_16.0.0_98a08e2...
