Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
(Maybe this isn't an ideal place for issues with your web site, but I could see no better one.)
There is a technical non-conformance in your nordicsemi.com domain. In practice...
I've been testing my application and am having an issue opening MasterEmulator sometimes. I need to reseat the nfr51 dongle to clear out the errors I am seeing below. Any...
Hi,
I get error NRF_ERROR_INVALID_PARAM or error 0x12 from sd_ble_gap_connect in central.
I even changed peer_addr.type to 0 (BLE_GAP_ADDR_TYPE_PUBLIC).
When scanning find...
Hi, I'm trying to use an MDBT40 based board as a sniffer using the NRF sniffer firmware. I'm guessing I just need UART -> USB to talk to the chip, so I've hooked it up to...
Hi,
I am trying to figure out the best way to save power on the nrf52. I need to connect with ble about two times per day. The ble should 'woken up' by an accelerator ...
How can I flash both the dfu bootloader and an application, and have the application run after the flash?
As soon as I flash the bootloader, it kicks in doesn't fire the...
Hi,
While updating from the antique NRF51 SDK8.1.0 to the newer SDK 12.2.0, I came across a problem: Gcc crashed with:
c:\users\elm\documents\nordic\nrf5_sdk_12.2.0_f012efa...
Hi all,
i have some problem to use Timer0_IrQ.
i start first with a program that use a softdevice. After i want change this project with another that don't use it.
...
Hi,
I would like to know if the NRF51822 (Just the NRF board, not the BLE Nano) comes already prepared to be programmed or if it needs some modification. I want to program...
Hi,
I have successfully implemented the UART over BLE. Now I'm trying to implement the HID over GATT for my nrf8001 device. What I'm trying to achieve is lower connection...
Hello,
I am attempting to setup a SPIS interface, and I am continuously getting 0x00 inside my RX buffer. I am varying the length of TX from the SPI master, and seeing...
Hi,
Is nRF Sniffer able to trace BLE4.2 link with LE Data Packet Length extension?
I would like to be able to track the packets up to maximal theoretical data throughput...
Hi
i want to have a concurrent connection in nRF51822 with BLEs and some nRF24l01+.
is it possible ?
is available example
for it ? which SDK support ?
...
Hi, I am tring to build and compile the SDK 12 DFU bootloader_secure .
I am getting an error:
"unable to allocate space for sections/blocks with a total estimated minimum...
I am using nrf51822 Dongle with nordic-sdk_10 and s130 softdevice. Tried to flash the dfu bootloader and using examples/ble_peripheral/ble_app_dfu_template app for OTA.
...
