Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Al over these example programs there are all these messages like
LOG_INF ( "Filters matched. Address: %s connectable: %d " ,
addr , connectable );
How do you actually...
Hi,
We are using nrf52840 with nrfSDK-16.0. We have implemented extended advertisement in BLE 5 LE CODED PHY. We want to try periodic advertisements. Do we have any examples...
My custom device uses nRF9151 and we're using SDK 2.6.0 with modem firmware 2.0.1.
When the device connects to the LTE network it derives a default APN, however, my provider...
Hi,
I’m exploring the use of the Thread/Matter protocol for a smart lighting system. My goal is to have the system communicate seamlessly with the cloud—allowing commands...
I am using a LattePanda 3 Delta running an Ubuntu server OS (x86) headlessly. I am using a RS-232 cable to obtain the modem trace from my custom board, which uses an nRF9160...
Hi,
We are currently starting a project using the nRF52832 as our controller, Segger Embedded Studio 5.42a as our IDE, and nRF5 SDK version 17.0.2.
Project Requirement...
I have found a bug in SDK v2.6.0 at zephyr/drivers/flash/nrf_qspi_nor.c while erasing the external MX25R64 flash.
Environment:
nRF5340 DK Hardware (MX25R64 external...
Hi
We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
HW: nRF5340DK NCS: v2.8.0
After installing NCS v2.8.0 from ToolchainManager, I tried to build the project but failed.Error message "No such file or directory: LIBGCC_FILE_NAME...
I have a Raspberry Pi Pico which is powered by a Lipo battery. I want to measure the current with the Power Profiler Kit II. I hooked the 2 grounds to to the board, and VIN...
I am using BLE mesh in nrf52840. I have modified the sensor server sample and sensor client sample to suit my requirements. I am using toolchain and sdk v2.6.1. It is working...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
Hi
For a low power product, I need the nRF54L15 to wake up periodically with very low consumption in between. In the deepest sleep mode there is no RAM retained and so the...
So I've been trying out the nRF9161DK, and had a lot of problems creating builds with the included samples. Mostly CMAKE errors.
Guess I'm missing some basic knowledge here...
As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you
NCS 2.6.0
NRF52840
