after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am currently working on nrf52832 and trying to change the sampling frequency to 10KHz ,ie, 100us and keeping buffer samples as 1.
Previously in the example we...
In the product specification of nPM1100, for fixed 500mA charging limit, ISET should be connected to VSYS. In the USB-configuration (Configuration 3) ISET is connected to...
Hi:
We want to test the nrf7002 WIFI performance based on the nrf7002 PDK.Do we have relevant test firmware?
We noticed that the sdk document of V2.1.2 has a description...
hi.
I have a firmware using standard GATT, now im implementing the mesh layer.
Im using SDK 17.0.2 + MESH 5.0.0. (im not using the new sdk connect because it is very difficult...
I'm moving from NRF9160DK to a custom board, where it has no UART. I plan to just use RTT for debugging messages.
However, I found if I delete the section which defines...
Hi,
I build secure_bootloader_ble_s132_pca10040_debug example (SDK17.1) on SES 6.30.
The only modification to the project is excluding SEGGER_RTT_Syscalls_SES.c.
...
It is possible to addressing nodes using MAC address of the device in Thread network?
In topology: PC <-> Border router <-> Thread mesh nodes
which IPv6 (Mesh-Local EID...
Hello
I'm new to the nrf platform and wanted to try out the I2C functionality of my nrf5340 DK. The only example I could find was the Fujitsu MB85RC256V FRAM I2C example...
Hi,
We are nearing production stage of our project, and are looking at programming on a large scale. Using the nRF9160 we need to program the latest modem firmware along...
I have a broadcaster and a central device. The broadcaster beacons data every 60sec and goes to sleep, a configuration I have considered for minimal power consumption. Now...
During tests with a "User controlled PLMN selector with Access Technology '6F60'" one device stuck in a curious state:
nRF9160 SICA B0A mfw v1.3.3 CAT-M1, PSM: PTAU 24h...
Hi Nordic community:
Can we configure nRF52840 to support a 1.3 V VIO?
I see from the datasheet, after the internal regulator, what supplies to the chip is actually...
Getting an error from mcumgr and I'm not sure where I should start debugging this.
My environment:
nRF Connect version 2.1.0 Board: nrf52840 DK and nrf52832 DK Host: MacOS...
Hello,
I'm developing with nRF5280-DK, using Zephyr-OS with mbedtls for the cryptography, and I need to have DES and 3DES enabled by default.
I tried to set in the prj...
Hi,
In a ble_app_uart example I have problems to send long packets if the Android smartphone only accepts MTU sizes of 20 bytes. I'm using the nRF5_SDK_17.1.0, the S132...
