Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
In the Zigbee Network Coordinator example when flashing new file to nrf52840-DK the Zigbee network steering automatically starts. How do I disable auto-start of network...
I have allocated 100 pages for FDS, but now i dont have enough space for the DFU. ir there a way to use FDS space (im happy to loose data stored in FDS), for the BLE DFU?...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
I work on a project that uses the dfu target library for firmware updates. This has been working flawless until I added task watchdogs.
The problem that I see is that...
Hi,
I am using a ISP3010 SiP which inludes a nrf52832, a DW1000 and the corresponding antennas (built-in antenna).
I have a custom board (board1) as reference, where the...
I added custom data to default asset_tracker_v2. The custom data is properly encoded and displayed in JSON format in LTE and acknowledged by Azure IOT, but it seems that the...
Hello,
We're working with nRF52833 & nRF52840 and I'm trying to figure out why we've ~0.3ms IRQ Latency from the moment I call the function " uart_irq_tx_enable (dev );...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
Hi,
My customer use nRF52840 with nRF5 SDK 15.0.0.
They have come up against the difficulty that uart RX pin instability.
I have searched the DevZone and it's advised...
Hi Nordic Community
I have been building a thermometer device from which I would like to send temperature values via periodic advertising.
I have based the sender and...
HI
I am beginner, I have a question , is necessary to put both crystal in circuit configuration?,
in my application i am using nrf_calendar example like a watch, may be...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
I added ring buffer and UART ASYNCH interface to asset_tracke_v2. I added CONFIG_RING_BUFFER = y, CONFIG_SERIAL = y and CONFIG_UART_ASYC_API = y to prj.conf file. The build...
The nrf52 is waking from a sd_power_system_off() and resets. The reset reason register indicates it was from a DETECT from GPIO, yet the LATCH register is 0 and all the sense...
