Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi guys,
I am trying to flash my nrf52840 dongle (with the Segger j-link mini) via your awesome NRF Connect Extension on my Apple M1, but I can't get it to work inside of...
I was able to work with the spi module, but now I want to make it work like a simulator, so I updated the configuration function and tried it like this.
Could you please...
Hello everyone,
I am trying to implement the OPTIGA Trust M from Infineon with the nrf9160. Unfortunately I encountered some problems regarding this topic.
I am trying...
Hi,
I'm working with the nrf52840, and I've had success with spi communication in the past. However, I want to switch to spim and am unsure how to do so. Can you provide...
Hey, Having some trouble getting the callbacks to invoke with the generic library on zephyr 1.7.1 to my understanding once it gets the data it should call it. have i misunderstood...
It is a very basic question.
For SOC firmware development with Segger and SDK, which layers of BLE are codes covering? Are Host and controller layers transparent to developers...
Hello,
Due to a routing error, the VBUS pin of the nRF52840 is connected to the GND.
The software works on the devkit but not on my prototype.
From what I saw in...
Hi！
Where master and slave is connecting, and then master is shutdown or move far away.Slave is wait for timeout.But the current of average slave e electric current
...
For my project I need to set the UART0 speed to 9600 baud.
So for testing I tried to compile the "Hello word" example by setting the board configuration file (ncs\v1.6.1...
CONFIGURACION:
NRF52 + SDK15 + SD132 + FREERTOS + NUS.
I have a task sending many packages to a central. I'm having an aboslutly aleatory behaviour: - At some time (could...
I’m checking the transaction of the data between iPhone and a Bluetooth device.
The device is developed by a business partner, but I’m not concerned the FW. I think we have...
Hi,
I am using nRf SDK5 and have a sensor that I am trying to extract the Eddystone UID data from the advertising packet. It shows up in nRfconnect as:
Eddystone UID...
I installed the nrf connect 3.91 with programmer v2.0.1 and J-Link driver v6.88a. However, when I cant seem to see the dev kit on my windows 10. I tried holding the reset...
Hi everyone,
I want to use the RTC module in my code, and I have some questions.
1. What I have understood so far is that the nRF52840 has three RTCs (RTC0, RTC1, RTC2...
