We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi , I have a problem when I wanted to combine the two examples twi scanner and usbd ble uart together although they work correctly individually I have a MAX30105 sensor which...
Hi all
We're developing an application for nrf9160 with zephyr-sdk v2.4.99-ncs2 and nrf-sdk v1.5.1.
In our project we are required to use a Library which forces us to...
Hello
I want to sampling two analog.. with different configuration and handler.
so I set two channels like this.
and then I call only one sample function like...
I'm working on developing a device using the nrf52832. Currently using the nrf52 PCA10040 dev kit. I'm extending the zephyr/samples/basic/peripheral_dis sample in order to...
When compiling the net CPU with debugging configs such as CONFIG_DEBUG or CONFIG_DEBUG_OPTIMIZATIONS enabled and the resulting hex is flashed to the nRF5340; If then an Ozone...
Hi I am wanting to use the ARDUINO 4 RELAYS SHIELD with the nrf52480 or at least see if its possible.
https://store.arduino.cc/arduino-4-relays-shield
relay data sheet...
I wanna use nRF52820 to make some application development.I wanna a sing-board development kit for nRF52820 ,and nRF52833DK supports development on the nRF52820 SoC and nRF52833...
Hi Everyone This is my first time designing a PCB with the NRF51822. I have designed it using an 2450AT18B100E Antenna and a BAL-NRF02D3 balun. Below is my schematic:
...
There are discussions on WLCSP light sensitivity for nRF5 product, which affects RF, clock accuracy, and low power current draw etc. what about the nPM1100 which clock accuracy...
Is my understanding correct that with VDD supplied and ENABLE = high, having VDD_GPIO floating (i.e. disconnected from a regulated 3.3 V supply) is a valid state? We intend...
hello Nordic
i am working with nrf52840 sdk16.0 s140
i wish to read the UICR register value like this :
but i get this compilation error
since it is a define...
Hello, I'm working the nrfx saadc legacy driver, and despite changing whether I measure Vdd(on the dk) or GND, the saadc output(p_event->data.done.p_buffer[0]) oscillates...
SDK14.0+NRF52832（PCA10040 demo board）:
I want to add static passkey to avoid MITM attack， I write code as following, but when I use the mobile app ‘nRF Connect’ to connect...
Dear community,
I need to operate a BM833A as I2C slave and to do so, I performed the following steps:
I modfied my sdk_config.h and set TWIS_ENABLED and NRFX_TWIS_ENABLED...
Hi,
I used nRF Connect for power profiler and programmer for hundreds of times.
But since today, it just keeps on showing white screen.
I tried "Ctrl + R" as well as...
