Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I am pretty new the BLE development stuff and was mostly working on an application that works with an existing connection. But because my colleagues are not able...
I am using nrf52832 ble, I want to set the pin P0.2 low as analog input and p0.3 high as analog input .
#define AIN0 2 // analog pin p0.2
#define AIN1 3
#define AIN0_PIN_CONFIG_HIGH...
SDK: 16
Mesh SDK: 410
Example: Light Lightness Server.
I discovered a bug when using the "Move Level" message that doesn't allow the LED to turn off after the move...
hello sir/ma'am
we are using nrf52840 chip in our customized board product and IAR as a development environment and also a debugger called segger jlink .we are not able...
Hello
we are thinking of using the nrf52832 (sdk 16.0, s132) , which we are a bit familiar with by now.
We have a project in which we need to transmit data to 150 unit...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1. I am using ‘ble_app_blinky’.
I am new to BLE certification. I have few queries on BLE Certification...
Hi Team,
I have down loaded the "pc-nrfutil-6.1.zip" from git repository and started the execution by using python commands. while running i am getting some errors.
...
Using PWM control 2.7KHZ buzzer, it can work normally when I don't turn on the broadcast. Every time I turn on the radio, the buzzer seems to blend in with different frequencies...
Hi
Based on zigbee sdk 3.2, add the device to the network, call zb_bdb_is_factory_new() after Joined network successfully, it returns true;
The same is true on zigbee...
Hello,
I am working with nRF52DK, I am trying to implement grouped SAADC for three sensors,
I want to receive all three ADC outputs at the same time on development kit...
Hello,
While working with a bare metal (no SoftDevice or OS) test application to prove code functionalities, I ran out in a weird behaviour that I cannot explain.
I'm...
Hi,
I started to implement the nrf ppm driver into my application. It is a smart connected grand light.
My goal is to smoothly fade the connected power LEDs on, hold for...
Hello,
So I have the following setup. I have an nrf9160 DK board. With the following hardware.
A base shield: https://www.reichelt.com/ch/de/arduino-shield-base-shield...
Hello,
I am using the att_mtu_max_throughput example from SDK 15. I am using an nRF52 as tester and nRF52840 DK as receiver.
I have modified the example slightly so that...
