To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
I've tried to install nRF Connect v2.0 on both Win 7 and Win 10 systems, both running Avast Anti-virus (up to date). In both cases the antivirus gives a warning about IDP...
I have the Memory Manager module enabled in my custom sdk_config. Within the module, I have both of the following defined.
MEM_MANAGER_ENABLE_LOGS 0
ENABLE_DEBUG_LOG_SUPPORT...
Hello - Is the long range option programmable in BT 5.0? During the run time, is it possible to switch between high speed and long range mode dynamically depending on the...
I am specific about master as I have to connect two simultaneously(obviously to two different pins pair). Plz provide any code outline if you have, Thank you in Advance
Hi.
I would like upload firmware from Atmel microcontroller to nRF51822 with SD130.
I suppose that I have to use single_bank_serial_s130 in nRF51822AA, but what I have to...
Hi,
I'm trying to implement dfu bootloader over uart, not dfu bootloader over air.
Where can I find a reference source code of dfu bootloader over uart?
regards ...
Hi,
We have to find the battery life of a central device based on nRF52 (s132 v3 soft device)running with 800mAh battery. The device scans for a peripheral in every 5 sec...
Hi!
I am trying to measure the current profile of a pca10056 board using an oscilloscope. I cut SB40, as per instructions in the User Guide and powered it using only a...
Hello,
Are there any rules for how to use the manufacturer specific ID in a beacon-format advertisement? For example:
In this example:
byte 0-2: 02 01 06 = flag...
I've used DFU alongside with HRS and it seems to work fine.
This time I'm using a custom service and I'm trying to add a DFU alongside. They just don't seem to play well...
Hi, I successfully modified the Nordic Semiconductor SDK 13's SAADC example adding a feature that performs the FFT of the sample taken and using an RTC is possible also to...
hi :
i following the online LWM2M example document of iot-sdk and setup leshan bs server on ubuntu 16.04 of VM.
i run bs server on ubuntu16.04 of VM and run LWM2M example...
Hi all,
sometimes this events occurs on my code. My start point was the glucose app, to implemented a "just work" pairing and bonding.
When this event occurs a disconnect...
Hello,
one of my project requirement is that i can accept data via bluetooth and rf. i want to know can we use bluetooth and rf in same code. the switching between bluetooth...
